2
Failure/Error Display Codes
NOTES:
■
Always disconnect power before touching internal parts of the oven.
■
Upon replacement, immediately return old electronic oven control
using the mailing label supplied with each new control.
A. Oven cavity display
B. Latch switch state
C. Door switch state
D. Model select state
E. Main cavity temperature
F. Secondary cavity temperature
G. Meat probe temperature
H. Warm drawer temperature
(if applicable)
B
A
C
D
E
F
H
G
Model Select State
Description
01
Thermal convection oven
07
Self-clean oven
To Enter Diagnostics Mode:
Before proceeding with any corrective action, perform the following
steps to enter the Diagnostics mode.
1.
To recall last failure code, if not displayed, press the OFF key to
place the oven in an idle state.
2.
Enter Diagnostics mode and verify error codes by pressing OFF,
OFF, START.
3.
If control does not enter Diagnostics, repeat steps.
Screen 1:
■
Main clock hours display shows latch state in first display position,
and door state in second position.
■
Main clock minutes display shows the model select state
associated with control system.
■
Main temperature display shows the cavity temperature.
■
Lower text line shows software versions for appliance manager
(AM), user interface (UI) and EEPROM version.
Press key #6 to scroll to next screen.
Screen 2:
Displays programmed to cavity size.
Press key #6 to scroll to next screen.
Screen 3:
Displays the last error code in memory. If GOOD is displayed, there is
not an error coded in memory.
To Clear Last Error Code
1.
Unplug oven or disconnect power.
2.
Wait 10 seconds, reconnect or plug in oven.
3.
Enter Diagnostics mode by pressing OFF, OFF, START.
4.
Press key #6 to show cavity size select screen.
5.
Press key #6 to show error code.
6.
To edit press CLOCK key.
7.
Press START key to clear last error. Control should display GOOD.
Troubleshooting Key strokes
■
Press the Bake key to activate Bake relay.
■
Press Broil key once to activate Outer Broil, press again for Inner
Broil.
■
Press Convect Bake key to activate Convect Ring and Fan.
■
Press Self Clean key to activate Latch Motor.
■
Press Cook time key once to activate low speed, press again for
high speed.
FAILURE (Leftmost
2 Clock Digits)
ERROR (Rightmost
2 Clock Digits)
LIKELY FAILURE
CONDITION
F0
E0
No error(s) found
SUGGESTED CORRECTIVE ACTION PROCEDURE
(Good) No corrective action required
F1
Internal
E0
Replace oven user
interface
SUGGESTED CORRECTIVE ACTION PROCEDURE
PROCEDURE: Before proceeding, perform steps 1 through 3 of “To
Enter Diagnostics Mode.”
1.
Unplug oven or disconnect power.
2.
Replace the user interface.
3.
Replace all parts and panels before operating.
4.
Plug in oven or reconnect power.
5.
Verify operation is normal. Go to Step 1 of “To Enter Diagnostic
Mode” and complete checks.
F1
Internal
E1
Replace oven
appliance manager
SUGGESTED CORRECTIVE ACTION PROCEDURE
PROCEDURE: Before proceeding, perform steps 1 through 3 of “To
Enter Diagnostics Mode.”
1.
Unplug oven or disconnect power.
2.
Check wiring to both switches on the door latch between the latch
and the control. If wires to either switch contact ground, they can
cause this error.
3.
Check wiring to oven temperature sensor(s). If OK, check resistance
values for oven temperature sensor(s) to ensure they are in the
correct range. Sensors having resistance values out of range will
cause this error.
4.
Check oven door switch. If there is no error, go to Step 5.
5.
Replace oven appliance manager.
6.
Replace all parts and panels before operating.
7.
Plug in oven or reconnect power.
8.
Verify operation is normal. Go to Step 1 of “To Enter Diagnostic
Mode” and complete checks.
FAILURE (Leftmost
2 Clock Digits)
ERROR (Rightmost
2 Clock Digits)
LIKELY FAILURE
CONDITION
