Kitagawa TT200BE-01 Скачать руководство пользователя

Страница: 38 / 69

12-2. Backlash adjusting method of tilting axis drive spur gears (See Fig.11)

The adequate backlash of spur gear is 0.02mm

～

0.04mm. If the measured backlash is deviated, it is

necessary to adjust the backlash.

1) Drain lubrication oil from the tilting axis lubrication oil drain port (See outline drawing).

2) Slightly loosen four mounting bolts

③

which fix the motor.

3) Insert a rod

①

(approximately

5, a bar wrench may also be used) in the hole located above the

motor and operate it to lower the motor position until the backlash becomes zero (0) approximately.

4) Insert a rod

②

(approximately

5, a bar wrench may also be used) in the hole located below the

motor and operate it to move the motor until the backlash falls within the adequate range (0.02 mm -

0.04 mm). At this time, check the motor movement with the dial gauge attached to the motor side.

5) Tighten four mounting bolts

③

that loosened slightly.

6) After adjusting, run the motor from slow speed to high speed to check that abnormal noise does not occur.

When mounting the motor, take care so that O-ring

④

will not be

damaged.

Mounting bolt

③

O-ring

④

CAUTION

Fig.11

Round bar

①

Round bar

②

Motor

Содержание TT200BE-01






































































Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды

Kitagawa TT200BE-01, Инструкция по эксплуатации

Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды