Kitagawa M0915RA Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 52

Kitagawa M0915RA Скачать руководство пользователя страница 28

MA0882RHG

27

7. Maintenance and Inspection

7-1. Maintenance and inspection of the cylinder

○

If any malfunction occurs, return cylinder to our company for repair. If it is disassembled

and reassembled at a place other than our company, it may not function correctly as

well as cause precision failure.

○

If rust or mist adheres to the gap between the detectable plate and the rotary valve, the

sliding resistance will increase and the detectable plate may be damaged. Check the

gap between the detectable plate and the rotary valve for sticky substances about once

a year. If there is sticky material, clean it and remove it. Follow the procedure below for

cleaning. Please refer to (1-4. Parts list on pages 7 and 8). Removing parts, make a

matching mark on each part as a mark when reassembling.

①

Move the cylinder to the back end.

②

Remove the A to C port pipes and drain pipes.

③

Remove the Socket button head cap screw [23] (3 places), and then remove the

ring [9].

④

Remove sticky material while spraying lubricant on the gap between the inner

diameter of the detectable plate [8] and the outer diameter of the rotary valve [4].

⑤

After connecting the hydraulic port, repeat the push-pull operation of the cylinder

several times to confirm that there is no problem.

Assemble in the reverse order of disassembly.

Tighten the Socket button head cap screw with the specified tightening torque.

(M6: 8.6 N

・

m)

・

If mist adheres to the cylinder, improve the environment so that it does not adhere. If

there is a lot of adhesion, the sliding resistance of the detectable plate will increase,

and the detectable plate may be damaged.

・

If there is a lot of mist adhering and disassembly and cleaning is required, send it

back to our company for cleaning.

7-2. Maintenance and inspection of hydraulic unit

○

Clean the suction strainer every 2 to 3 months.

○

Replace the hydraulic oil about once every six months.

«
...
26
27
28
29
30
...
»

Содержание M0915RA





















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды