Kirisun PT8200 Скачать руководство пользователя страница 14

Страница: 14 / 15

N Problem Solution

C.The IC U101 of phase lock loop is

broken.Please change IC.

5 The red

transmission

Indicator lights

but no sound

is heard.

3 No talkback

4 No receiving

signal

A.The frequency is not right. Please reselect

the channel of the same frequency.

B.The CTCSS/DCS code is not the same.

Please reset it.

C.Please check the TX/RX signalling system

of both.

D.It is out of the effective communication

range.

E.The FM IC U101 is broken. Please

change IC.

A.The power-amplifier tube Q23/Q25 is

broken, resulting in no power output.

Please change it.

B.The microphone is broken. Please change

it.

D.The battery is out of power. Please charge

or change it.

E.CPU is broken, Please change the IC.

2 Phase lock

loop

unlocked

(Beeping)

A.The crystal X1 of phase lock loop is broken.

Please change it.

B.The oscillator tube is broken. Please

change it.

A.The antenna is not in good contact. Please

fasten the antenna head.

B.The high-frequency amplifying tube Q26 is

broken. Please change it.

C.The squelch level is set to high Please

reset the squelch level.

D.The mixed tube Q21 is broken. Please

change it.

The green

receiving dicator

lights but no

sound is heard.

C.The power amplifier U201 is broken.

Please change it.

A.The speaker is broken. Please change it.

B.The audio power amplifier U11 is broken.

Please change IC.

14. Major Specifications

Frequency Range: 136MHz--174MHz 350MHz--400MHz

400MHz--470MHz 450MHz--520MHz

Channel Number: 128 (divided into 16 zones and

at most 16 channels per zone)

Channel Spacing: 25 kHz (wide band)/ 20 kHz (medium band)

/12.5 kHz (narrow band)

Operating Voltage: 13.6V DC

10%

Содержание PT8200
















Результаты поиска

Содержание PT8200

Отзывы:

Похожие инструкции для PT8200

Бренды по названию

Популярные бренды

Kirisun PT8200, Инструкция по эксплуатации

Результаты поиска

Содержание PT8200

Отзывы:

Похожие инструкции для PT8200

Бренды по названию

Популярные бренды