Kirisun DP580-01 Скачать руководство пользователя

Страница: 63 / 69

User Manual

a) Keep the microphone 3~10 cm from your mouth.

b) During the dwelling time, press the PTT key to talk, and the red indicator glows.

c) Wait until the prompt tone for voice communication ends, and then speak to the microphone.

d) Release the PTT key to receive voice.

e) If you do not respond during the dwelling time, the radio will go on to scan other channels.

7) Deleting Noise Channel

If bad calls or noise are generated frequently in a channel, you can delete the channel temporarily by

pressing and holding the programmed Delete Noise Channel key.

Note:

A channel cannot be deleted if it is the only one prior channel or selected channel or the only one in the

scan list.

11.7

GPS*

If positioning system is enabled, the radio will display and offer location information to the software server

Содержание DP580-01






































































Результаты поиска

Содержание DP580-01

Отзывы:

Похожие инструкции для DP580-01

Бренды по названию

Популярные бренды

Kirisun DP580-01, Руководство пользователя

Результаты поиска

Содержание DP580-01

Отзывы:

Похожие инструкции для DP580-01

Бренды по названию

Популярные бренды