manualshive.com logo in svg

KINNEY KVC Series, Руководство оператора, Страница: 6 / 44

Поделиться
Скачать
KINNEY KVC Series Скачать руководство пользователя страница 6

2

Manual 1866    Rev A    p/n 1866

CONVENTIONS AND DATA PLATE

02

GRAPHIC CONVENTIONS IN THIS 
MANUAL

The following are hazard levels referenced within 

this manual:

DANGER

!

Indicates a hazardous situation that, if not 

avoided, will result in death or serious injury.

WARNING

!

Indicates a hazardous situation that, if not 

avoided, could result in death or serious 

injury.

CAUTION

!

Indicates a hazardous situation that, if not 

avoided, could result in minor or moderate 

injury.

Indicates a situation that can cause damage 

to the engine, personal property, and/or 

the environment or cause the equipment to 

operate improperly.

OTE:  

N

Indicates a procedure, practice, or 

condition that should be followed in 

order for the equipment to function in the 

manner intended.

CAUTION

!

Read manual before operation 

or bodily harm may result. 

Attention should be given to the 

safety related sections of this 

manual.

WARNING

!

Keep body & clothing away 

from machine.
During operation, keep body 

and clothing away from inlet 

and outlet of the pump.

WARNING

!

Do not operate without guards 

in place. Assure that the guards 

are in place and secure prior to 

operation.

Содержание KVC Series













































Отзывы:

Нет отзывов