manualshive.com logo in svg

KINNEY KVC Series, Руководство оператора, Страница: 19 / 44

Поделиться
Скачать
KINNEY KVC Series Скачать руководство пользователя страница 19

15

Manual 1866    Rev A    p/n 1866

06

OPERATION

WARNING

!

Improper use may lead to severe or fatal injuries. 
Therefore be sure to obey the safety instructions.

CAUTION

!

Hot surfaces. When the machine 
is at operating temperature the 
surface temperature on the 
components may go above 158°F 
(70°C).You must avoid touching 
the hot surfaces. These areas are 
marked with warning plates.

CAUTION

!

Noise emission. The highest 
noise pressure levels measured 
as per EN ISO 3744. When 
spending a long time in the vicinity 
of the running machine use ear 
protection to avoid permanent 
damage to your hearing.

Wait until the machine stops. The machine 

must only be switched on again after it stops.

CHECKING ROTOR 
ROTATION DIRECTION

Operating in the wrong direction of rotation leads 

to damage to the machine. Use a phase sequence 

indicator to check the direction of rotation 

(clockwise rotating field).

The intended direction of rotation of the drive 

shaft is shown by the rotary direction arrow on the 

motor flange. Start the motor briefly (maximum of 

2 seconds) to check the direction of rotation. When 

looking at the motor fan, it must rotate counter-

clockwise.

Содержание KVC Series













































Отзывы:

Нет отзывов