When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury to individuals.
1. Read and understand all directions.
2. Follow all warnings and instructions.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water.(i.e. Near a bathtub, kitchen sink, washing
machine, in a wet basement, or near a swimming pool.) Avoid spilling liquid
on the product.
5. Do not place this product on an unstable cart, stand, or table. Serious
Damage may occur to the product if it falls.
6. Do not allow anything to rest on the telephone cord. Do not locate this
product where the cord might be damaged by persons walking on it.
7. Never put foreign objects of any kind into the product as they may touch
dangerous voltage points or short out parts that could result in a risk of fire or
electrical shock.
8. To reduce the risk of electric shock, do not disassemble this product, take it
to a qualified service person if service or repair work is required. Opening or
removing cover may expose you to dangerous voltages or other risks.
Operate after Incorrect reassembly can cause electric shock.
9. Adjust only the controls that are covered by the operating instructions.
Improper adjustment of controls may result in malfunction that could require
extensive work by a qualified technician.
10. Refer servicing to qualified service personnel if the following should occur:
If the phone line or plug is damaged or frayed.
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following operating instructions.
If the product has been dropped or the cabinet has been damaged.
If the product exhibits a distinct change in performance.
IMPORTANT SAFETY INSTRUCTIONS
11
12. CHANGE PIN CODE
The default pin code is 1234.
Enter menu, select [SETUP], press [OK/Menu] to bring up sub-menus,
select [CHANGE PIN CODE] and press [OK/Menu] to access pin code
setting page, enter 4 digits old pin code, press [OK/Menu] and then enter
4 digits new pin code, press [OK/Menu] to confirm.
11. Avoid using a telephone during an electrical storm. There may be risks of
electric shock from lightning.
12. Do not use the telephone in the vicinity of a gas leak.
13. The handset receiver may retain dangerous materials such as metallic
pins and staples because the receiver is magnetic.
TROUBLE SHOOTING GUIDE
PROBLEM SOLUTION
Phone does not ring Make sure phone line cord is connected
to base unit and wall jack
Ringer volume is too low Check if ringer volume set on low (see
page 11 for HS Ringer Vol adjustment)
Phone receives but cannot Is the dial mode in accordance with the
make calls local telephone company
10
FCC Interference Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference; and (2) This device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is
“receiving” the interference).
• Reorient or relocate and increase the separation between the elecommunications equipment and
receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the
receiving antenna is connected
FCC RF Radiation Exposure Statement
The installation of the base unit should allow at least 20 centimeter between the base and persons to
be in compliance with FCC RF exposure guidelines. For body worn operation, the portable part
(handset) has been tested and meets FCC RF exposure guidelines.
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
The changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
