background image

17 

ATTACHING TO TRACTOR continued.... 

 

 

STEP 4 

        Pull apart PTO shaft and attach outer section to tractor PTO output shaft.  

NOTE:  Be sure to pull on PTO shaft section to ensure yoke has locked into 
place. 

  STEP 5 

 

         Place and hold inner PTO shaft section next to outer section and check if PTO 

shaft  is  too  long.    Each  section  should  end  approximately  3  inches  short  of 
reaching u-joint shield on the opposite section.  If the shaft is too long measure 
3 inches back from each u-joint shield and mark the other shaft section.  Be sure 
to do this for both PTO shaft halves.  NOTE:  Do not cut PTO shaft sections at 
this time. 

 

STEP 6 

       Raise rotary tiller and remove blocking.  Raise and lower rotary tiller in order to 

locate the longest distance between equipment input shaft and the tractor PTO 
output shaft.  With the rotary tiller in the longest distance position shut down the 
tractor and SECURELY BLOCK THE ROTARY TILLER IN POSITION. 

 

 

STEP 7 

       As  in  step  5  hold  PTO  shaft  sections  together  and  check  for  a  minimum  of  6 

inches of overlap.  If PTO shaft has been marked for cutting the overlap is the 
distance measured between the two marks.  If the PTO shaft has less than a 6 
inch overlap, DO NOT USE.  Contact your authorized King Kutter  Dealer. 

 

 

NOTE 

 

If the PTO shaft length is too long go to

 SIZING PTO SHAFT (pg. 18)

  

 

 

STEP 8 

        Apply  any  multi-purpose  grease  to  the  outside  of  the  male  (inner)  PTO  shaft 

section.  Assemble PTO shaft and install on rotary tiller and tractor. 

 
 

STEP 9 

        Pull on tractor side of PTO shaft yoke to be sure it has locked in place.  Make 

certain PTO shaft shielding is in place and good working condition. 

 

STEP 10 

       The  PTO  shaft  shield  is  a  non-rotating  design  and  must  be  secured  prior  to 

equipment use.  Using the chain on each yoke shield attach to a fixed object on 
the tractor and equipment ends that will not allow the PTO shaft shield to rotate 
during operation.   

Содержание TG-48-XB





































Отзывы: