background image

OPERATIONAL SAFETY

 continued... 

 

 

Pass rotary mower diagonally through sharp dips and avoid sharp drops to pre-
vent “hanging up” tractor and rotary mower.  Practice will improve your skills in 
maneuvering on rough terrain.  Always cut down slopes, never across the face. 
Always check tractor manual for proper use on slopes. 

 
 

When using a unit, a minimum 20% of tractor and equipment weight must be on 
tractor front wheels.  Without this weight, tractor could tip over, causing personal 
injury or death.  The weight may be attained with a front- end loader, front wheel 
weights, ballast in the tires or front tractor weights.  When attaining a minimum 
20% of tractor and equipment weight on the front wheels, you must not exceed 
the ROPS weight certification.  Weigh the tractor and equipment.  

Do not guess 

or estimate!

 

 
 
TRANSPORT SAFETY 

 

 

Comply  with  state  and  local  laws  governing  highway  safety  and  movement  of 
farm machinery on public roads. 

 

The use of flashing amber lights is acceptable in most localities. However, some 
localities  prohibit  their  use.    Local  laws  should  be  checked  for  all  lighting  and 
marking requirements. 

 

At all times, when driving the tractor and equipment on the road or highway un-
der 20 mph (32 kph) use flashing amber warning lights and a slow moving vehi-
cle  (SMV)  identification  emblem.    Do  not  exceed  20  mph  (32  kph).    Reduce 
speed on rough roads and surfaces. 

 

Plan your route to avoid heavy traffic. 

 

Always install transport locks, pins or brackets before transporting. 

 

Do not drink and drive. 

 

Be a safe and courteous driver.  Always yield to oncoming traffic in all situations, 
including  narrow  bridges,  intersections,  etc.    Watch  for  traffic  when  operating 
near or crossing roadways. 

 

Turn curves or go up or down hills only at a low speed and at a gradual steering 
angle.    Make  certain  that  a  least  20%  of  the  tractor’s  weight  is  on  the  front 
wheels to maintain safe steerage.  Slow down on rough or uneven surface. Al-
ways check tractor manual for proper use on slopes. 

 

Use  extreme care and  maintain  minimum  ground and when  operating  close to 
ditches or fences.  Be careful when turning sharp corners. 

 

Never allow riders on either tractor or mower. 

 

16

 

Содержание 999998

















































Отзывы: