background image

INSTRUCTIONS FOR KC-2102FXR

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

COPYRIGHT © 2007 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.

21” WOOD BANDSAW

WITH RESAW GUIDE AND CAST IRON BLADE WHEELS

Resaw guide

Resawing is a method of ripping a piece of lumber into thinner pieces as
well as making book matched or slip matched panels. The curved resaw
guide (A) Fig.1 is the best option for guiding wood through the bandsaw.
The narrow line of contact makes it easy to compensate for a blade that
“leads” or wanders off the cutting line when the stock is fed straight into it.
You can get satisfactory results with this resaw guide “single point” method,
but it demands very careful hand control. 

To install resaw guide;

1) Attach the resaw guide post (A) Fig.2 to the fence (B) using washer (C)

and lock handle (D).

2) Slide and position the resaw guide post so that it is centered with the

front edge of the blade and tighten lock handle.

Here’s how you can resaw precisely and easily using resaw guide. Pencil a
straight line down the edge of a square edged board. Start sawing along
your layout line, guiding the board freehand. If the blade is leading, you will
have to feed the board into the blade at an slight angle to keep cutting along
the line and to compensate for blade drift. See Fig.1.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most 
updated parts diagram and parts list.

2-YEAR LIMITED WARRANTY FOR KING INDUSTRIAL MACHINERY

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this improved product are available at our authorized King Canada service centers across Canada.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the original
retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from defects in
materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence or accidents, repairs
done by an unauthorized service center, alterations and lack of maintenance. King Canada shall in no event be liable for death, injuries to
persons or property or for incidental, special or consequential damages arising from the use of our products. 

To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an authorized King
Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our authorized service
centers. In cooperation with our authorized serviced center, King Canada will either repair or replace the product if any part or parts covered
under this warranty which examination proves to be defective in workmanship or material during the warranty period.

Figure 2

Figure 1

Содержание KC-2102C










Отзывы: