background image

IMPORTANT INFORMATION

22--Y

YEEA

AR

LIMITED WARRANTY

FOR THIS 12” X 36” METAL LATHE 

K

KIIN

NG

G C

CA

AN

NA

AD

DA

A TTO

OO

OLLSS

OFFERS A 2-YEAR LIMITED WARRANTY

FOR INDUSTRIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this tool are available at our authorized KING CANADA service centers across Canada. For servicing, contact

or return to the retailer where you purchased your product along with your proof of purchase.

LIMITED TOOL WARRANTY

KING CANADA makes every effort to ensure that this product meets high quality and durability standards. KING CANADA warrants to

the original retail consumer a 1-year limited warranty as of the date the product was purchased at retail and that each product is free

from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or  accidents,

repairs or alterations and lack of maintenance. KING CANADA shall in no event be liable for death, injuries to persons or property or

for incidental, special or consequential damages arising from the use of our products. To take advantage of this warranty, the product

or part must be returned for examination by the retailer. Shipping and handling charges may apply. If a defect is found, KING CANADA

will either repair or replace the product.

K

KIIN

NG

G C

CA

AN

NA

AD

DA

A TTO

OO

OLLSS IIN

NC

C.. D

DO

OR

RV

VA

ALL,, M

MO

ON

NTTR

REEA

ALL,, Q

QU

UEEB

BEEC

C,, C

CA

AN

NA

AD

DA

A H

H99PP 22Y

Y44

Содержание KC-1236ML














Отзывы: