background image

6

EN

The light will stay on for the entire opening manoeuvre and for the 

subsequent  pause  time;  during  the  closing  manoeuvre  both  the 

green and red lights will be activated (the result being yellow) to indi-
cate there is no longer any transit priority (see table).

Table 1

Red

Green

Meaning

OFF

OFF

Bar closed, no passage in either direction

OFF

ON

Bar open, free transit

ON

OFF

Bar open, transit occupied

ON

ON

Bar closing and transit not controlled

The two Bar Open Indicator and Courtesy Light outputs can directly 
control small 24 V DC lamps for a total of 10 W. If stronger lamps have 
to be used, use the relays piloted by the unit outputs that control, in 

turn, the traffic lights.

IMPORTANT! - It is best to fit the radio receiver at this point, 

once all adjustments have been completed and with the pow-

er switched off.

3.7 - 

Description of the functioning  

modes

In the manual functioning mode the OPEN input allows movement 
up to the opening point; the CLOSE input allows movement up to 
the closing point; STEP-BY-STEP allows alternative opening and clos-
ing manoeuvres; as soon as the command in input stops, movement 
stops. In the opening phase movement stops when the maximum 
opening point is reached or if there is no consent from PHOTOCELL 
2; to the contrary, in the closing phase movement will stop at the max-
imum closed point or if there is no consent from the PHOTOCELL. If 
STOP is triggered it will cause movement to stop immediately both in 
the opening and closing manoeuvres. Once movement has stopped 
the command in input has to be stopped before any new movements 
can be active)
In either of the automatic functioning modes (semiautomatic-auto-
matic and closes always) a command on the OPEN input will cause 
an opening manoeuvre; if the command remains (TIMER) once the 

bar is open, the bar remains “frozen” in an infinite pause; only when 

the command stops will the bar be able to close. Command pulses 
on the CLOSE input will cause a closing manoeuvre; if the command 
remains the bar will stay locked in the closed position until the com-
mand ceases and only then can it be reopened. A pulse on STEP-BY-
STEP causes alternative opening and closing.
A second pulse on the STEP-BY-STEP or on the same input that 
started the movement, will cause a Stop.

Whether in the opening or closing phase, if STOP triggers it will cause 
movement to stop immediately.
In an opening manoeuvre, triggering of the PHOTOCELL has no ef-
fect while PHOTOCELL 2 will cause reversal of movement; in a clos-
ing manoeuvre, triggering of the PHOTOCELL causes movement to 
reverse followed by a new pause and lastly reclosing. If at the begin-
ning of an opening movement, the PHOTOCELL input does not give 

consent, the request to open is cancelled.

If the automatic functioning mode is being used, there will be a pause 

time subsequent to an opening manoeuvre and followed by a closing 

manoeuvre. If, during the pause the PHOTOCELL triggers, the timer 
will be reset with a new time; if, on the other hand, a STOP comes 
into play during the pause, the reclosing function will be cancelled and 
there will be a STOP condition.

3.8 - 

Charge card also battery 

 

powered

The road boom gate is equipped with a power transformer that can 
withstand the energy required by both the motor and electronic card 

so it can all be powered directly by the mains.
If you want the system to work even when there is a power cut then 
you have to add a suitable battery and relative battery charger card.
The battery must be installed in its own compartment outside the 
plastic box that protects the gearmotor card and connected to two 
terminals on the battery charger card; the latter must be connected to 
the connector on the unit.

4. 

Technical featurs of the unit

Open4000 technical features

Mains power

230 V AC ± 10%, 50-60 Hz

Battery power

21-28 V DC (> 6Ah capacity)

Max. current accessories, 24 V DC

200 mA

Max. power flashing light

25 W [24 V DC]

Max. power Courtesy Light

10 W [24 V DC]

Max. power Open Bar indicator

10 W [24 V DC]

Pause time

from 3 to 120 seconds

Courtesy light time

60 seconds

Operating temperature

-20 to 70° C

Содержание STAR OPEN









Отзывы: