1. KNOW YOUR TOOL
Read and understand the instruction manual and labels affixed to the tool. Learn its
application and limitations as well as its specific potential hazards.
2.
Don’t use power tools in damp or wet locations or expose them to rain. Keep work area
well lit and provide adequate surrounding work space.
3. USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it was not designed.
4. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they could
get caught in moving parts. Non-slip footwear is recommended. Wear protective hair
covering to contain long hair. Roll up long sleeves above the elbows.
5. MAINTAIN TOOL WITH CARE.
Keep tool clean for best and safest performance. Follow instructions for operation and
maintenance.
6. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
7. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ‘’OFF’’ position before plugging in.
8. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the instructions that
accompany the accessories. The use of improper accessories may cause hazards.
9. CHECK FOR DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are damaged should be
carefully checked to ensure they will operate properly and perform their intended
function. Check for alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other parts which are damaged
should be properly repaired or replaced.
Specific Safety Instructions
1. Only use
King attachments and accessories, serious injury can result if this warning is
not respected.
2. Before filling with water or changing an accessory,
remove the power cord from the
power source. This will prevent accidental starts and possible electrocusion.
3. Wear protective gloves and safety glasses,
an accessory can become extremely hot
during operation, danger of burns!
4. Do not use the tool
if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
5. Do not jam hand tool.
Do not jam tool to sharpen against the wheel. Hold tool firmly
with both hands and slowly apply tool against wheel using light pressure.
6. Replace wheel as needed.
When the wheel has worn down, a replacement wheel
(model KM-096) is available, see maintenance instructions.
7. Never
sharpen more than one tool at a time.
8. For wet sharpening,
run wheel in water bath for one minute to make sure the wheel is
completely wet.
GENERAL & SPECIFIC
SAFETY INSTRUCTIONS
ELECTRICAL INFORMATION
WARNING!
ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED
ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! ALL
ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE WET/DRY
SHARPENER DISCONNECTED FROM THE POWER SOURCE. FAILURE TO
COMPLY MAY RESULT IN SERIOUS INJURY!
POWER SUPPLY
WARNING:
YOUR WET/DRY
SHARPENER MUST
BE
CONNECTED TO A 110V, 15-AMP.
BRANCH CIRCUIT. FAILURE TO
CONNECT
IN THIS WAY
CAN
RESULT IN INJURY FROM SHOCK
OR FIRE.
110V OPERATION
As received from the factory, your
wet/dry sharpener is ready to run for
110V operation. This tool is intended
for use on a circuit that has an outlet
and a plug which looks like the one
illustrated in Fig.1.
EXTENSION CORDS
The use of any extension cord will cause some
loss of power. Use the following table to
determine the minimum wire size (A.W.G-
American Wire Gauge) extension cord. Use only
extension cords which accept the tool’s plug.
For circuits that are further away from the
electrical circuit box, the wire size must be
increased proportionately in order to deliver ample voltage to the motor. Refer to Fig.2 for
wire length and size.
FIGURE 1
FIGURE 2
110V GROUNDED OUTLET
GROUNDING
PLUG
CURRANT
CARRYING
PRONGS
Tool’s
Amperage
Rating
0.1-6
6-8
8-10
10-12
12-16
Cord Size in A.W.G.
Cord Length in Feet
25
50
100 150
18
16
16
14
18
16
14
12
18
16
14
12
18
16
14
12
14
12
-
-
