1. KNOW YOUR TOOL
Read and understand the instruction manual and labels affixed to the tool. Learn its
application and limitations as well as its specific potential hazards.
2.
Don’t use power tools in damp or wet locations or expose them to rain. Keep work area
well lit and provide adequate surrounding work space.
3. USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it was not designed.
4. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they could
get caught in moving parts. Non-slip footwear is recommended. Wear protective hair
covering to contain long hair. Roll up long sleeves above the elbows.
5. MAINTAIN TOOL WITH CARE.
Keep tool clean for best and safest performance. Follow instructions for operation and
changing accessories.
6. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
7. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ‘’OFF’’ position before plugging in.
8. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the instructions that
accompany the accessories. The use of improper accessories may cause hazards.
9. CHECK FOR DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are damaged should be
carefully checked to ensure they will operate properly and perform their intended
function. Check for alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other parts which are damaged
should be properly repaired or replaced.
Specific Safety Instructions
1. ALWAYS SWITCH OFF AND WAIT.
Wait for the sanding belt to come to a complete stop before any type of adjustment or
maintenance.
2. KEEP HANDS AWAY FROM MOVING PARTS.
3. KEEP CHILDREN AND PREGNANT WOMEN
away from the work area where paint
sanding is being done.
4. ALWAYS WEAR A DUST MASK
or respirator, the mask filter should be replaced regularly.
5. NO EATING, DRINKING OR SMOKING
should be done in the work area to prevent
ingesting contaminated paint particules.
We recommend you save these instructions
GENERAL & SPECIFIC
SAFETY INSTRUCTIONS
ELECTRICAL INFORMATION
WARNING
: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
Note: Performance of this tool may vary depending on variations in local line voltage.
Extension cord usage may also affect tool performance.
VOLTAGE WARNING
Before connecting the tool to a power source (receptacle, outlet, ect.) be sure the voltage
supplied is the same as that specified on the nameplate of the tool. If one says 120V and
the other says 115V then there will be no complications. Never try to plug a 120V tool into
a 240V outlet, or the other way around. A voltage greater than that specified on the tool
can result in
SERIOUS INJURY
to the user, as well as damage to the tool. If in doubt,
DO
NOT PLUG IN THE TOOL
.
DOUBLE INSULATION
Double insulated tools are equipped with a polarized two-prong plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install a polarized outlet. Do not alter or change the plug in any way. Double insulation
eliminates the need for three wire grounded power supply and grounded power cords.
EXTENSION CORDS
Improper use of extension cords may cause inefficient operation of your tool which can
result in overheating. Be sure your extension cord is rated to allow sufficient current flow
to the motor. If you are using the tool outdoors, use an extension cord rated for outdoor
use (signified by “WA” on the jacket).
The extension cord must have a minimum wire size depending on the amperage of the
tool and the length of the extension cord. This size is determined by its AWG (American
Wire Gauge) rating. The smaller the gauge, the greater the cable’s capacity. The amount
of cords used does not matter: Total length determines the minimum AWG rating. Every
cord must meet the AWG rating. Use the chart below to determine what AWG rating is
required for your situation. Cord length is rated in feet.
Tool’s
Amperage
Rating
3-6
6-8
8-10
10-12
12-16
Cord Size in A.W.G.
Cord Length in Feet
25
50
100 150
18
16
16
14
18
16
14
12
18
16
14
12
18
16
14
12
14
12
-
-
Electrical Specifications
Voltage ....................................110-120V
Amperage ........................................7.2A
Cycle/Phase ....................60Hz, 1 phase
