King Canada 8348VS Скачать руководство пользователя страница 4

OPERATION

USING YOUR MULTI-TOOL
WARNING:

Do not plug in power cord until the

accessory is installed securely to the tool. 

Wear

protective gloves and safety glasses,

an accessory

can become extremely hot during operation, danger of
burns!

On/Off Switch

To turn the multi-tool on, push the switch (A) Fig.2
towards the front. To turn tool off, push the switch
towards the back. 

Do not use the tool

if switch does not

turn it on or off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.

Variable Speed Selector Dial

This tool comes with a variable speed selector dial, to
increase speed, turn selector dial (A) Fig.3 towards the
right, to decrease speed, turn selector dial towards the
left.

Securing Workpiece

Use clamps or any other practical way to secure and
support the workpiece to a stable  platform. Holding the
work by hand or against your body is unstable and may
lead to loss of control and injury.

SAWING
35mm Narrow Tru-cut Saw Blade- 

Saws wood, plaster

board and soft plastics up to 50mm thick. Plunges easily into any point in the material.

HSS Segment Saw Blade- 

Ideal to cut wood, plastics, fiberglass, putty, even sheet metal

and non-ferrous metals (up to 1mm).
Tip: The segment saw blade can be secured in an offset position to provide uniform wear.

SANDING
Sanding Back-up Pad- 

Multi-tool sands effortlessly and precisely in corners and edges.

Tips: Only dry sand wood or metal. When only one tip of the sanding paper is worn, the
sanding paper can be pulled off, turned and reinstalled to use a unused corner.

SCRAPING
52mm Rigid Scraper Blade- 

Removes lacquer, carpeting, tile adhesives and underseal

coatings.

OPTIONAL ACCESSORIES AVAILABLE

Other accessories are available for this multi-tool, refer to the list below. Contact your
nearest King Canada distributor for more information and availability. These accessories
will fit King, FEIN

®

and other brands having a 10mm mounting hole.

Model KW-4801

- 1pc. HSS Segment Saw Blade.

Model KW-4802

- 1pc. HSS Segment Flush Cut Saw Blade with depressed centre.

Model KW-4803

- 1pc. Carbide Abrasive Saw Blade with depressed centre.

Model KW-4804

- 1pc. Triangular Carbide Rasp with depressed centre.

Model KW-4805

- 3pc. Tru-cut Saw Blades Kit (35, 20 & 10mm).

Model KW-4807

- 19pc. Sanding & Scraping kit. Includes Sanding Pad, 15 Sanding Papers

(60, 80, 120 grit), Rigid Offset Scraper Blade, Flexible Non Offset Scraper Blade & FEIN

®

Cap Screw.

Figure 2

Figure 3

MAINTENANCE

MAINTENANCE

IMPORTANT

: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustments should be performed by an authorized service center or other qualified
service technician, always using identical replacement parts.

1. Air vents of the tool should be cleaned regularly to avoid overheating of the motor which

is caused by the blocking of the air vents.

2. DON’T clean this tool with water, as no liquid is allowed in the tool body. Clean the tool

with a dry clean cloth only. Compressed air at low pressure is also suitable.

3. DON’T allow petroleum based products to come into contact with the plastic parts of the

tool, as they contain chemicals that can damage or destroy the plastic parts.

CARBON BRUSHES

Remove and check the carbon brushes regularly
(normally after 50 hours of use). The carbon brushes
are installed inside the motor housing. Using a
screwdriver, remove the pan head screw that holds
the motor housing cap in place, this screw can be
found at the back of the motor housing, just above the
power cord protector.

Slide the motor housing backwards until the carbon
brushes are exposed. To remove a carbon brush (A)
Fig.4 from the motor housing, insert the tip of a small
flat screwdriver into the side opening of the holder,
this will release the carbon brush clip (B), pull out
carbon brush and inspect it. Repeat this step for the second carbon brush. Carbon
brushes need to be replaced once they wear down. Keep the carbon brushes clean and
free to slip in the holders. 

If they have worn down, replace them with the set of carbon brushes supplied with this kit.
If you have lost the supplied set, you will need to purchase a set of identical replacement
carbon brushes (both carbon brushes should be replaced at the same time). Install new
carbon brushes and reinstall the motor housing cap using the pan head screw.

If you are unsure about these instructions, we recommend that you get a qualified service
technician to replace the carbon brushes. Contact a King Canada service centre.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram
and parts list.

Figure 4

Отзывы: