9
8
[DE translation]
Installation der Gummitülle
1. Stecken Sie die Gummitülle in das Loch in der Lauffl
äche
2. Pressen Sie die Gummitülle so tief hinein, bis sie mit den
Gummilippen anliegt
Installation des Magneten
3. Legen Sie den Magneten auf die flache Fläche eines
Schraubenziehers (er hält dort von alleine)
4. Pressen Sie mit dem Schraubenzieher den Magneten in die
Gummitülle
5. Drücken Sie den Magneten so tief hinein, bis er mit der
Gummitülle bündig abschließt. Nutzen Sie den Schraubenzieher
dazu
6. Überprüfen Sie nochmals das bündige Abschließen mit dem
Schraubenzieher
Sensor Installations-Richtlinien
Der Magnet muss über der Kerbe des Sensors sitzen (in einer
Linie)
Die Sensor-Kanten müssen an den roten Pfeilspitzen anliegen
Installation des Sensors
7. Reinigen Sie die Plastikoberfläche, so dass sie schmutz- und
fettfrei ist
8. Ziehen Sie die Folie von der Klebefläche auf der Rückseite des
Sensors ab
9. Positionieren Sie vorsichtig den Sensor auf dem
Verbindungsbügel und pressen ihn fest.
HINWEIS: Die richtige
Ausrichtung ist wichtig. Sensorkanten müssen an den Kanten des
Verbindungsbügels anliegen.
BEFORE YOU START
: Kinetic T-2005 inRide Power
Sensors pair with apps using the Bluetooth Smart
communication protocol (a.k.a. Bluetooth 4.0, Bluetooth
LE or BLE) found in most mobile devices manufactured
within the past 5 years or with Garmin computers and
watches using the ANT+ communication protocol.
PAIRING BEST PRACTICES USING BLUETOOTH AND
MOBILE DEVICES
inRide sensors and heart rate monitors pair directly with
training apps and NOT within the device settings like
wireless headphones or an earpiece.
Do not pair your
trainer or heart rate monitor in your device settings
, even if
the device will let you as some Android devices will. In your
device SETTINGS > BLUETOOTH, if you see your sensor
listed please delete it and follow the directions below.
• Download and install the soft ware you’d like to use.
We
recommend that all customers start with the Kinetic
Fit app.
• Open the Kinetic Fit app and create an account.
• SELECT PROFILE from the menu in the lower left corner
of the app and configure your profile
• With inRide sensor installed and bike mounted on
trainer, wake up your inRide sensor by pedaling your
bike for a few turns.
• Pair to the Fit app: Open the Fit app and select
SENSORS from the menu on the bottom left of the
app screen. Your inRide sensor should show on the
SENSORS screen. Select the CHAIN LINK ICON. It will
turn green when paired. (All training apps will have a
similar process for pairing. Just make sure the trainer or
sensor is active before trying to pair to any 3rd-party
app.
• On the Kinetic Fit app home screen, select WORKOUT
button on bottom of screen and choose a workout.
• Select a WARMUP and start riding. Each Kinetic Fit
workout includes a 10-minute warmup followed by a
spindown calibration. Once calibration is complete,
actual workout begins.
For additional information:
https://support.kurtkinetic.
com/hc/en-us/categories/200442600-Kinetic-Fit-App
https://www.kurtkinetic.com/training-blog-feed/
getting-started-with-zwift
Connect with Training Apps
COMMON PAIRING ISSUES (sensors not showing in app)
• Dead battery in inRide or HR sensor - replace battery.
• Sensor has been paired to Bluetooth in device settings
instead of the chosen training app - delete sensor in
device settings and re-pair through Kinetic Fit app.
RESETTING INRIDE SENSOR
• Hard quit the Fit app by double tapping the home button
and upswiping the app if it’s on. (varies with device type)
• In your device settings, turn off Bluetooth.
• Power off your device.
• Pull battery from sensor and install it upside down.
• While your sensor battery is flipped, power up your
device, turn on bluetooth again in settings, open the Fit
app, and open the Sensors screen.
• Flip the battery back to positive side up in the sensor and
reinstall battery cap. If this doesn’t work, try it again with a
fresh battery. (a magnet helps with battery removal)
