Wireless KINETIC Switch needs no internal power supply, battery or wiring, it has only an RF switch (transmitter) and
a control (receiver) unit. The switch can be placed anywhere on the wall, on consoles or it can also be used in motion
because it requires no wiring.
Operation:
The control (receiver) unit can be connected to any device of which operating voltage is not more than 1000W
(180V-260V AC (50/60Hz) on operating voltage). These devices can be switched on or off by the Wireless KINETIC
Switch (transmitter unit). By pushing the Switch, a mechanism process induces voltage to to the transmitter which
forwards the sign to the receiver to switch on or off the connected device. The speed and time of pushing the switch
cannot affect the operation. Range in open space is approx. to 70 m.
Installation:
Connect the control unit to the device and power supply following the given illustration (1.).
Place or fix the Wireless KINETIC Switch anywhere. To fix the device, flip the tumbler part of the switch off by a slotted
screwdriver, then you can fix it through 2 borehole by the screws. Finally, flip the tumbler back to its place (2.).
Pairing:
Push the pairing button on the control unit for approx. 5 mp (as it is shown on 1. picture - F), then push the Wireless
KINETIC Switch twice (in 1 minute). You can pair more than one receiver and transmitter at the same time.
Warning:
Improper use or installation can cause damage, serious injury, or electrical shock. Consult a qualified electrician.
- do not place the transmitter and the receiver to wet environment
- do not disassemble or modify the circuits of the device
- fix the device properly
- do not exceed the specified electronic data
- turn off power at circuit breaker before installing the unit
Control Unit (Receiver)
Wireless KINETIC Switch
Power
180V-260V AC (50/60 Hz)
no separate power supply
Operating Temperature
-10°C - +50°C
-40°C - +50°C
Range
70 m
Operating RF
433 Mhz
Energy consumption
<750 mW
-
Max capacity (device)
1000 W (min. 5 W)
-
Size
66 x 41 x 27 mm
85 x 85 x 13 mm
Weight
35 g
58 g
The set includes:
1 x Wireless Kinetic Switch; 1 x Receiver; 1 x 3M sticker; 2 pairs x Magnetic nuts and screws; 2 pairs x Screws and
dowels; 1 x User Manual
A vezeték nélkül KINETIC kapcsoló egy külső tápellátás nélküli, elemet vagy hálózati feszültséget nem igénylő rá-
diófrekvenciás kapcsolóból (adó) és egy vezérlőegységből áll (vevő). A kapcsoló tetszőlegesen felhelyezhető és
rögzíthető bármilyen falra, konzolra vagy akár hordozva is használható, semmilyen vezetékezést nem igényel.
Működése:
A vezérlő (vevő) egységre bármilyen fogyasztó ráköthető, melynek a teljesítménye nem haladja meg az 1000W tel-
jesítményt (180V-260V AC (50/60Hz) üzemi feszültségen). Ezeket a vevőre rákapcsolt fogyasztókat lehet be- és ki-
kapcsolni a vezeték nélküli KINETIC kapcsolóval (adó). A kapcsoló megnyomásakor egy mechanizmus feszültséget
indukál az adó egységnek, mely jelet küld a vezérlőnek a fogyasztó be- vagy kikapcsolására. A kapcsoló megnyo-
másának sebessége és ideje nem befolyásolja a működést.
Hatótávolsága nyílt terepen közel 70 m.
Beüzemelés:
Kösse rá a vezérlő egységet a fogyasztóra és hálózati feszültségre a megadott ábra alapján (1.).
Helyezze el vagy rögzítse a vezeték nélküli KINETIC kapcsolót egy tetszőleges helyen. Az esetleges rögzítéshez pat-
tintsa ki a kapcsoló billenő részét egy lapos csavarhúzó segítségével, ezután 2 db furat mentén csavarral rögzíthető,
ezt követően óvatosan pattintsa vissza a billenő részt (2.).
Wireless KINETIC Switch / Vezeték nélküli KINETIC kapcsoló /
Întrerupător fără fir KINETIC / Bezdôtové KINETIC tlačítko
55350