Kikusui PFX2532 Скачать руководство пользователя | Manualshive

Страница: 83 / 142

background image

PFX2532

83

PFX2532 Electric Specifications

5

Specific

a

tions

General specifications

Nominal input rating

100 Vac to 240 Vac, 50 Hz/60 Hz

Input voltage range

90 Vac to 250 Vac

Power consumption

60 VAmax (when three OP02-PFXs are installed:
80 VAmax)

Operating temperature and humidity range

0 °C to 40 °C (32 °F to 104 °F), 20 %rh to 85 %rh (no
condensation)

Storage temperature and humidity range

-10 °C to 60 °C (14 °F to 140 °F), 0 %rh to 90 %rh (no
condensation)

Operating environment

Indoors, overvoltage category II

Altitude

Up to 2000 m

Isolation
voltage

I/O terminals

⇔

chassis

±70 Vmax

Insulation
resistance

Primary

⇔

chassis

500 Vdc, 30 MΩ or greater, 70 %rh humidity or less

Primary

⇔

I/O terminals

Withstandin
g voltage

Primary

⇔

chassis

No abnormalities at 1500 Vac for 1 minute

Primary

⇔

I/O terminals

Safety

1

1

Does not apply to specially ordered or modified PFX2532s.

Complies with the requirements of the following directive
and standards.

Low Voltage Directive 2014/35/EU

2

EN 61010-1 (Class I

3

, Pollution Degree 2

4

)

2

Limited to products that have the CE mark on their panels.
When the optional OP03-PFX Voltmeter Unit is used, compliance is achieve by using the optional TL12-PFX
sensing cable (length: approx. 3 m, connector area: with cover, with core).

3

This is a Class I equipment. Be sure to ground the PFX2532's protective conductor terminal. The safety of this
product is only guaranteed when the product is properly grounded.

Electromagnetic compatibility (EMC)

Complies with the requirements of the following directive
and standards.
EMC Directive 2014/30/EU

EN 61326-1 (Class A

5

)

EN 55011 (Class A

, Group 1

6

)

EN 61000-3-2
EN 61000-3-3

Applicable under the following conditions

The maximum length of all cabling and wiring

connected to the PFX2532 is less than 3 m.

Dimensions, weight

See the outline drawing. Approx. 17 kg (37.48 Ib)

Accessories

Power cord

7

1 pc. with no plug

I/O terminal cover set

Three terminal covers, six cable ties for locking

I/O terminal M8 screw set

6 sets

Load input terminal cover set

Cover, four auxiliary bands

26-core flat cable

1 pc. DC power supply connection I/F cable (for PWR)

Ferrite core for 26-core flat cables

1 pc.

20-core flat cable

1 pc. Electronic load connection I/F cable

Ferrite core for 20-core flat cables

1 pc.

26-core cable (with ferrite core)

1 pc. DC power supply connection I/F cable (for PAT-T)

Sensing connector

1 pc.

Sensing connector cover set

One cover set, one cable tie for locking

Thermistor

1 pc.

Lock lever

2 pcs.

LAN cable

1 pc. Straight type

Operation manual (this manual)

1 copy

«
...
81
82
83
84
85
...
»

Содержание PFX2532















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PFX2532

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: Wavelink Страницы: 69

Бренд: Calpeda Страницы: 4

Бренд: Daikin Страницы: 38

Бренд: Daikin Страницы: 2

Бренд: Daikin Страницы: 148

Бренд: Daikin Страницы: 12

Бренд: Daktronics Страницы: 52

Бренд: Waeco Страницы: 20

Бренд: Z-Wave Страницы: 56

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: K&K Страницы: 6

Бренд: National Instruments Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды