manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 17 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 17

KHA3000

17

No.

Name

Function

Page

1

POWER switch

Turns the power ON ( ) or OFF ( )

72

2

USB

For USB flash drive.

273

3

MEMORY slot

For CompactFlash card.

272

4

Display unit

Mounted with LCD backlight.

85

5

F1 to F6 keys

Function keys for menu selection.

82

6

Small knob

Rotary knob for setting menu details.

82

7

Operation unit

Keys and large knob. Enlarged view is shown under front panel view.

84

8

Handle

Handle for carriage.

46

9

Leg/stand

Adjusts the angle of front panel.

46

10

Rubber pads on side 
surface

4 positions on side surface.

46

11

ASSIST key

Explanatory function supporting operation.

90

12

HA key (LED)

Harmonic current test modes

92

13

Vf key (LED)

Voltage fluctuation test modes

184

14

OTHER key (LED)

Other measurement modes

248

15

VIEW key (LED)

Selects measurement observation and test results analysis views 
(status display).

157

16

START key

Starts test.

128,210

17

STOP key

Stops test.

128,211

18

HOLD key

Holds screen measurement data variations.

85

19

HARD COPY key

Screen hard copy.

85

20

FILE key

Saves and opens test data file.

266

21

REMOTE LED/LOCAL 
key

Remote control status display/local setting.

84

KEY LOCK key

Key lock setting.

22

EXT CONT key

Sets external device control.

118,203

23

SYSTEM key

Sets test system.

86

24

0 to 9 and “.” and “-” keys

Input numeric values.

83

25

7

 V RANGE

Numeric key.

110

Selects voltage range and raises sensitivity.

26

4

 

V RANGE

Numeric key.

110

Selects voltage range and lowers sensitivity.

27

0

 

BUZZER

Numeric key.

85

Lowers buzzer volume.

28

1

 BUZZER

Numeric key.

85

Raises buzzer volume.

29

5

 I RANGE

Numeric key.

110

Selects current range and raises sensitivity.

30

8

 I RANGE

Numeric key.

110

Selects current range and lowers sensitivity.

31

ENTER key

Confirms entry.

83

32

ESC key

Returns from sub-menu to upper menu.

84

33

SHIFT key

Shift key.

3

34

keys

UP/DOWN and LEFT/RIGHT keys.

–

35

keys

UP/DOWN key.

85

BACK LIGHT 

key 

Sets the brightness of display unit.

36

Large knob

Rotary knob for numeric value entry and cursor setting.

83

See

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов