KidKraft Summerhill F29050 Скачать руководство пользователя страница 29

Страница: 29 / 68

2 x

Heavy SW Post 50.8 x 76.2 x 2201.9mm

1 x

SW Upright 76.2 x 76.2 x 1294.3mm

1 x

SW Support 23.8 x 82.6 x 1181.1mm

Step 7: Swing End Assembly

Loosely attach 2 (2613) Heavy SW Posts to (2615) SW Upright using 2 (G7) 5/16 x 5-1/2” Hex Bolts (with

lock washer, flat washer and t-nut). Notice 2 bolt holes at top of (2615) SW Upright and orientation of angle.

(fig. 7.1)

Attach (2616) SW Support to both (2613) Heavy SW Posts and (2615) SW Upright using 3 (G4) 5/16 x 4”

Hex Bolts (with lock washer, flat washer and t-nut). Tighten all bolts. (fig. 7.1)

Install 2 (WB7) 5/16 x 3” Wafer Bolts (with flat washer and t-nut) in the top bolt holes in (2615) SW Upright

as shown in fig. 6.1.

IT IS IMPORTANT THAT THESE BOLTS ARE ATTACHED. THEY WILL MINIMIZE

CHECKING OF WOOD.

Hardware

Wood Parts

2 x

Hex Bolt (lock washer, flat washer, t-nut)

3 x

Hex Bolt (lock washer, flat washer, t-nut)

2 x

Wafer Bolt (flat washer & t-nut)

WB7

Notice 2 bolt

holes at top and

orientation of

the angle

WB7

Fig. 7.1

2613

2615

2613

2615

2616

TN2

FW2

TN2

FW2

LW2

Содержание Summerhill F29050





































































Результаты поиска

Содержание Summerhill F29050

Отзывы:

Бренды по названию

Популярные бренды

KidKraft Summerhill F29050, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Summerhill F29050

Отзывы:

Бренды по названию

Популярные бренды