background image

12

16. TROUBLESHOOTING

Problem

Fan will not start.

Fan sounds noisy.

Fan wobble.

Remote control 
malfunction.

Solution

1. Check circuit fuses or breakers.
2. Check all electrical connections to insure proper contact. 

CAUTION:

 Make 

sure the main power is OFF when checking any electrical connection.
3. Make sure the transmitter batteries are installed properly.  Positive (+) side 
facing out.
4. Insure the batteries have a good charge.

1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade brackets to the motor are 
tight.
3. Make sure wire nut connections are not rubbing against each other or the 
interior wall of the switch housing. 

CAUTION:

 Make sure main power is off.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan 
disappear during this time.
5. If using an optional light kit, make sure the screws securing the glassware are 
tight. Make sure the light bulbs are not touching any other component.
6. Do not connect this fan to wall mounted variable speed control(s).  they are 
not compatible with ceiling fan motors or remote controls.
7. Make sure the upper canopy is a short distance from the ceiling. It should not 
touch the ceiling.

1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal. 
Check this level by selecting a point on the ceiling above the tip of one of the 
blades. Measure this distance. Rotate the fan until the next blade is positioned 
for measurement. Repeat for each blade. The distance deviation should be 
equal within 1/8".
3. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.
4. If the blade wobble is still noticeable, interchanging two adjacent (side by 
side) blades can redistribute the weight and possibly result in smoother 
operation.

1. Ceiling Fans with remote control systems CAN NOT be operated in 
conjunction with any other control system EXCEPT a basic On/Off wall switch, 
if desired.

80” Lehr

TM

18. WARRANTY CONDITION

Please contact the retail outlet where the fan was purchased for a warranty service.

17. SPECIFICATIONS

These are approximate measurements.  They do not include data for any lamps or fixtures 
attached to the ceiling fan.

30.8

kgs

N.W.

33.0

kgs

G.W.

3.97'

C.F.

RPM

66

59

51

45

37

31

CFM

7407.77

6260.83

5364.05

4699.72

3955.96

3309.54

CFM/W

233.68

327.79

406.37

484.51

618.12

769.66

Fan Size 

80"

220-240

220-240

220-240

220-240

220-240

220-240

Volts 

0.45

0.28

0.20

0.15

0.11

0.07

Amps 

31.70 

19.10 

13.20 

9.70 

6.40 

 4.30  

Watts

Speed 

Extra-High

High

Medium High

Medium

Medium Low

Low

Содержание Lehr Decor 80"














Отзывы: