Keysight U2741A Скачать руководство пользователя страница 48

Страница: 48 / 54

U2741A USB Modular 5.5 Digits Digital Multimeter Service Guide

Service

Troubleshooting the modular DMM

This section provides a brief check list of common failures.
Before troubleshooting or repairing the modular DMM, make
sure the failure is in the instrument rather than any
external connections.

Unit is inoperative

•

Verify that the AC/DC adapter is connected to the
modular DMM.

•

Verify that the front panel power indicator is lit.

•

Verify that the USB cable is connected to the PC and the
USB inlet in modular DMM.

Current input is inoperative

Verify that the front panel 2 A, 250 V current fuse is
functional.

Power supply problems

Check that the AC/DC adapter is function and make sure
that its output voltage is 12 V.

Contact Keysight Technologies Service Centre to obtain
technical assistance, if necessary.

Содержание U2741A























































Результаты поиска

Содержание U2741A

Отзывы:

Похожие инструкции для U2741A

Бренды по названию

Популярные бренды

Keysight U2741A, Руководство по обслуживанию

Результаты поиска

Содержание U2741A

Отзывы:

Похожие инструкции для U2741A

Бренды по названию

Популярные бренды