Keysight N5247-60106 Скачать руководство пользователя страница 18

Страница: 18 / 54

18 Installation Note N5247-90106

Installation Procedure for the Upgrade

Step 9. Remove Some Bottom-Side (Test Set) Cables

1. Place the analyzer bottom-side up on a flat surface.
2. Remove all bottom-side cables (gray flexible and silver semi-rigid) except

for those in the following table. Do not discard the cables that are

removed because some will be reused later in the procedure.
To see an image showing the location of cables W11, W13, W23, W25,

W61, and W65, click the Chapter 6 bookmark “Top Cables, All Cables - All

Options” in the PDF Service Guide. To see an image showing the location

of cable W66, click the Chapter 6 bookmark “Bottom RF Cables, 2-Port,
Option 219” in the PDF Service Guide1.

Remove and discard the following gray flexible cables that have a top-side

connection:

—

W99 (N5247-60023) A16 SPAM board (J2) to A24 IF multiplexer (P603)

—

W100 (N5247-60024) A16 SPAM board (J5) to A24 IF multiplexer (P203)

Leave the remaining gray flexible cables, the wire harnesses, and the

ribbon cables connected where possible. Any that are removed should be

labeled for reconnection later.

Be careful not to damage the center pins of the semirigid cables. Some

flexing of the cables may be necessary but do not over-bend them.

When removing a cable, also remove the plastic cable clamp, if present. It

is normal for some of the cable clamp’s adhesive to remain.

Do Not Remove These Bottom-Side Cables

Reference

Designator Type

Part Number

Qty

Description

W11

N5247-20114

A7 port 1 40 GHz doubler P6 to W12

W13

N5247-20086 1

A7 port 1 40 GHz doubler P2 to W14

W23

N5247-20114

A8 port 2 40 GHz doubler P6 to W24

W25

N5247-20086

A8 port 2 40 GHz doubler P2 to W26

W61

N5247-20110

A15 13.5 GHz (LO) synthesizer board J1207 to A25 HMA26.5

W65

N5247-20113

A7 port 1 40 GHz doubler P5 to W66

W66

N5247-20109

W65 to rear-panel EXT TSET DRIVE RF OUT (J6)

a. SR = semirigid coaxial cable.

Содержание N5247-60106























































Результаты поиска

Содержание N5247-60106

Отзывы:

Похожие инструкции для N5247-60106

Бренды по названию

Популярные бренды

Keysight N5247-60106, Установочная инструкция

Результаты поиска

Содержание N5247-60106

Отзывы:

Похожие инструкции для N5247-60106

Бренды по названию

Популярные бренды