Keysight M8100A Series Скачать руководство пользователя

Страница: 35 / 46

Keysight M8100A Series Arbitrary Waveform Generators Getting Started Guide

Basic Setup for M8100A

Step 8 - Verify Basic M8199A Operation

After powering ON the connected hardware components, you can verify if

you have correctly set up the hardware if:
• a steady green status light is displayed on the ESM of the M9505A AXIe

Chassis indicating that the chassis has powered up successfully.

• the Access LED on the front panel of the instrument module turns on

indicating that the module is in a power- ready state.

• the Out of Service (OOS) LED on the front panel of the M9537A AXIe

Embedded Controller turns off. (Applicable only when you are using

M9537A AXIe Embedded Controller as the host computer).

If the chassis does not power up to a steady green Status light, or powers

up to a steady red light, the chassis has detected a failure and requires

service.

If the Fail LED on the front panel of the instrument module is steady red

and does not turn off, it indicates a power fault condition. In such a

situation, the instrument module may require repair/service.

Contact your Keysight representative to replace or service the

chassis/module. See

Contacting Keysight Service and Support

page 43.

Step 9 - Install Keysight IO Libraries Suite (not required for M8100A-BU6)

IO Libraries Suite version 17.1 or later is required. Always use the latest

version of the Keysight IO Libraries.

1 Disconnect any devices connected to the host computer.
2 If open, close all applications on the host computer.
3 Insert the

Automation-Ready

CD in your CD-ROM drive or download

and install the IO Libraries from

www.keysight.com/find/iosuite

4 Follow the instructions as prompted during the installation.
5 After installation, you will see the Keysight IO icon in the taskbar

notification area of the host computer screen.

NOTE

Perform this step if you are setting up an M8100A-BU5 system or the

host computer you are using as part of the M8100A system requires I/O

library installation.

Содержание M8100A Series















































Результаты поиска

Содержание M8100A Series

Отзывы:

Похожие инструкции для M8100A Series

Бренды по названию

Популярные бренды

Keysight M8100A Series, Руководство по началу работы

Результаты поиска

Содержание M8100A Series

Отзывы:

Похожие инструкции для M8100A Series

Бренды по названию

Популярные бренды