Keysight DSOX3012T Скачать руководство пользователя страница 360

Страница: 360 / 530

360

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Web Interface

The web interface for InfiniiVision X-Series oscilloscopes also provides help for

each of its pages.

Microsoft Internet Explorer is the recommended Web browser for communication

and control of the oscilloscope. Other Web browsers may work but are not

guaranteed to work with the oscilloscope. The Web browser must be

Java-enabled.

Before you can use the web interface, you must place the oscilloscope on the

network and set up its LAN connection.

Accessing the Web Interface

To access the oscilloscope's web interface:

Connect the oscilloscope to your LAN (see

“To establish a LAN connection"

page 343) or establish a point-to-point connection (see

“Stand-alone

(Point-to-Point) Connection to a PC"

on page 344).

It is possible to use a point-to-point connection, but using a normal LAN

connection is the preferred method.

Type the oscilloscope's hostname or IP address in the web browser.

The oscilloscope's web interface Welcome Page is displayed.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды