manualshive.com logo in svg

Keysight DSOX3012T, Руководство пользователя

Keysight DSOX3012T - мощный осциллограф с функциональностью отличного качества. Пользовательская инструкция доступна для бесплатного скачивания на manualshive.com. Используйте этот ресурс для получения подробной информации о продукте и его функциях. Идеальный инструмент для профессиональных и любительских проектов.

Поделиться
Скачать
background image

Utility Settings

22

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

343

 

To establish a LAN connection

Automatic

Configuration

1

Press 

[Utility] > I/O

.

2

Press the 

LAN Settings

 softkey.

3

Press the 

Config

 softkey; then, turn the Entry knob to select 

Automatic

, and press 

the softkey again to enable it.

If your network supports DHCP or AutoIP, enabling 

Automatic

 lets the 

oscilloscope use those services to get its LAN configuration settings

4

If your network provides Dynamic DNS, you can enable the 

Dynamic DNS

 option 

to let the oscilloscope register its hostname and use the DNS server for name 

resolution.

5

You can enable the 

Multicast DNS

 option to let the oscilloscope use Multicast 

DNS for name resolution on small networks without a conventional DNS server.

6

Connect the oscilloscope to the local area network (LAN) by inserting the LAN 

cable into the "LAN" port on the rear panel of the oscilloscope.

In a few moments the oscilloscope will connect to the network automatically.

If the oscilloscope does not automatically connect to the network, press 

[Utility] 

> I/O > LAN Reset

. In a few moments the oscilloscope will connect to the 

network.

Manual

Configuration

1

Get the oscilloscope's network parameters (host name, IP address, subnet 

mask, gateway IP, DNS IP, etc.) from your network administrator.

2

Press 

[Utility] > I/O

.

3

Press the 

LAN Settings

 softkey.

4

Press the 

Config

 softkey; then, turn the Entry knob to select 

Automatic

, and press 

the softkey again to disable it.

If Automatic is not enabled, the oscilloscope's LAN configuration must be set 

up manually using the 

Modify

 and 

Host name

 softkeys

NOTE

Any time you modify the oscilloscope's hostname, it breaks the connection between the 

oscilloscope and the LAN. You need to re-establish communication to the oscilloscope using 

the new hostname.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSOX3012T

Laica SB2200 Instructions And Guarantee preview
SB2200
Бренд: Laica Страницы: 4
ICS ELECTRONICS 4803 Quick Start Manual preview
4803
Бренд: ICS ELECTRONICS Страницы: 6
Datalogic Matrix 400 Quick Reference Manual preview
Matrix 400
Бренд: Datalogic Страницы: 20
Datalogic Matrix 320 Product Reference Manual preview
Matrix 320
Бренд: Datalogic Страницы: 188
Yamaha MagicStomp Effect List preview
MagicStomp
Бренд: Yamaha Страницы: 31
B.E.G. LUXOMAT net PBM-KNX-DX-4W Manual preview
LUXOMAT net PBM-KNX-DX-4W
Бренд: B.E.G. Страницы: 16
Qlight S180U Manual preview
S180U
Бренд: Qlight Страницы: 4
Marcy JD-2.1 Owner'S Manual preview
JD-2.1
Бренд: Marcy Страницы: 9
IKEA SPOKA Manual preview
SPOKA
Бренд: IKEA Страницы: 24
Life CIRCOLINA G10q T9 Instructions preview
CIRCOLINA G10q T9
Бренд: Life Страницы: 2
Teac BB-1000CD Release Notes preview
BB-1000CD
Бренд: Teac Страницы: 2
Bayer HealthCare Certegra Operation Manual preview
Certegra
Бренд: Bayer HealthCare Страницы: 104
Energizer EDC2-1001-RGB-MWT Quick Start Manual preview
EDC2-1001-RGB-MWT
Бренд: Energizer Страницы: 18
MIETHKE proGAV Instructions For Use Manual preview
proGAV
Бренд: MIETHKE Страницы: 125
Stamina 35-1050 Owner'S Manual preview
35-1050
Бренд: Stamina Страницы: 22
Cuisinart GRMC3E Original Instructions Manual preview
GRMC3E
Бренд: Cuisinart Страницы: 159
Power Dynamics DJ Laptop stand +tray Instruction Manual preview
DJ Laptop stand +tray
Бренд: Power Dynamics Страницы: 3
Kongsberg EM 712 Installation Manual preview
EM 712
Бренд: Kongsberg Страницы: 188

Бренды по названию

Популярные бренды

Загрузить еще бренды