Keysight DSOX3012T Скачать руководство пользователя страница 287

Страница: 287 / 530

Mask Testing

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

287

How is mask testing done?

InfiniiVision oscilloscopes start mask testing by creating a database that is 200 x

640 for the waveform viewing area. Each location in the array is designated as

either a violation or a pass area. Each time a data point from a waveform occurs in

a violation area a failure is logged. If

Test All

was selected, every active analog

channel is tested against the mask database for each acquisition. Over 2 billion

failures can be logged per-channel. The number of acquisitions tested is also

logged and displayed as "# of Tests".

The mask file allows greater resolution than the 200 X 640 database. Some

quantization of data occurs to reduce the mask file data for display on-screen.

NOTE

Although a mask can have up to 8 regions, in any given vertical column, it is only possible to

define 4 regions. When there are 4 regions in a vertical column, one region must be tied to the

top (using the MAX y value) and one must be tied to the bottom (using the MIN y value).

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды