Keysight Technologies U1450 Series Скачать руководство пользователя | Manualshive

Страница: 59 / 64

background image

Service and Maintenance

2

Returning the Instrument for Service

U1450 Series/U1461A Service Guide

57

Returning the Instrument for Service

Before shipping your instrument for repair or replacement, Keysight
recommends that you acquire the shipping instructions from the Keysight
Service Center. A clear understanding of the shipping instructions is
necessary to secure your product for shipment.

1

Attach a tag to the instrument with the following information:

•

Name and address of owner

•

Instrument model number

•

Instrument serial number

•

Description of the service required or failure indications

2

Remove all accessories from the instrument. Do not include accessories
unless they are associated with the failure symptoms.

3

Place the instrument in its original container with appropriate
packaging material for shipping.

If the original shipping container is not available, place your unit in a
container which will ensure at least 4 inches of compressible packaging
material around all sides for the instrument. Use static- free packaging
materials to avoid additional damage to your unit.

N O T E

Keysight suggests that you always insure your shipments.

«
...
57
58
59
60
61
...
»

Содержание U1450 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для U1450 Series

Бренд: Sperry instrument Страницы: 6

Бренд: Multitech Страницы: 111

Бренд: Jaycar Страницы: 24

Бренд: Miranda Страницы: 19

Бренд: Elma Страницы: 52

Бренд: Raisecom Страницы: 26

Бренд: National Instruments Страницы: 128

Бренд: Raisecom Страницы: 273

Бренд: Jeulin Страницы: 20

Бренд: Keithley Страницы: 936

Бренд: Meterman Страницы: 24

Бренд: Velleman Страницы: 112

MegaCastPlus USB-845 Series

Бренд: Vetra Страницы: 2

Бренд: TES Страницы: 23

Бренд: SW-Stahl Страницы: 30

Бренд: Phoenix Contact Страницы: 48

Бренд: Phoenix Contact Страницы: 142

Бренд: McCheck Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды