Keysight Technologies NFA X-Series Скачать руководство пользователя страница 90

Страница: 90 / 99

90 Keysight NFA X-Series Getting Started and Troubleshooting Guide

Troubleshooting
Check the Basics

Check the Basics

— Is there power at the receptacle?
— Is the analyzer turned on? Check to see if the green LED beside the power

switch is on. Also, listen for internal fan noise to determine if the analyzer

cooling fans are running.

— If other equipment, cables, and connectors are being used with your signal

analyzer, make sure they are connected properly and operating correctly.
If the analyzer cannot completely load or run the operating system, or the

instrument application is not successfully launched, the problem could be a

corrupt disk drive. If the analyzer gets far enough along in the boot process

to run the "Instrument Recovery System", perform the

“Disk Drive Recovery

Process”

as described on page 60.

— Is the Measurement Application running? If not, there is a software launch

shortcut/icon on the desktop.

— Does the instrument application have the focus? If not, move focus to the

application with Alt-Tab.

— Review the measurement procedures being performed when the problem

first appeared. Are all of the settings correct?

— If the analyzer is not functioning as expected, return the analyzer to a

known state by pressing

Mode Preset

— Is the measurement being performed, and the results that are expected,

within the specifications and capabilities of the analyzer?
Refer to the specifications guide for your analyzer.

h ttp://www.keysight.com/find/nfa_specifications

Technical manual pdf files are available on the Keysight website:

http://www.keysight.com/find/nfa_manuals

— If the analyzer is not communicating via the LAN connection, check for the

presence of blinking yellow LEDs on the rear panel LAN connector. If the

ACT LED is not blinking, check the LAN cable and LAN integrity.

— To meet specifications, the analyzer must be aligned. Either the Auto Align

(On) feature must be selected (press

System

Alignments

Auto Align

, and

select

Normal

), or the analyzer must be manually aligned.

— Perform an Alignment. Press

System

Alignments

Align Now

All

Some analyzer settings are not affected by a Preset. If you wish to reset

the analyzer settings, press

System

Power On

Restore Power On

Defaults

Содержание NFA X-Series




































































































Результаты поиска

Содержание NFA X-Series

Отзывы:

Похожие инструкции для NFA X-Series

Бренды по названию

Популярные бренды

Keysight Technologies NFA X-Series, Руководство по началу работы и устранению неисправностей

Результаты поиска

Содержание NFA X-Series

Отзывы:

Похожие инструкции для NFA X-Series

Бренды по названию

Популярные бренды