Keysight Technologies NFA X-Series Скачать руководство пользователя страница 17

Страница: 17 / 99

Keysight NFA X-Series Getting Started and Troubleshooting Guide 17

Quick Start
Instrument Information

Instrument Information

Power requirements

The only physical installation of your Keysight signal analyzer is a connection

to a power source. Line voltage does

not

need to be selected.

This analyzer does

not

contain customer serviceable fuses.

AC power cord

The analyzer is equipped with a three-wire power cord, in accordance with

international safety standards. This cable grounds the analyzer cabinet when

connected to an appropriate power line outlet. The cable appropriate to the

original shipping location is included with the analyzer.

The instruments can operate with mains supply voltage fluctuations up to

± 10% of the nominal voltage.

This is a Safety Class 1 Product (provided with a protective earthing

ground incorporated in the power cord). The mains plug shall only be

inserted in a socket outlet provided with a protective earth contact. Any

interruption of the protective conductor inside or outside of the product is

likely to make the product dangerous. Intentional interruption is

prohibited. (IEC 348 clauses 17.3.3c & 17.3.4)
Failure to ground the analyzer properly can result in personal injury.

Before turning on the analyzer, you must connect its protective earth

terminals to the protective conductor of the main power cable. Insert the

main power cable plug into a socket outlet that has a protective earth

contact only. DO NOT defeat the earth-grounding protection by using an

extension cable, power cable, or autotransformer without a protective

ground conductor.

This product is designed for use in Installation Category II and Pollution

Degree 2 per IEC 61010 Second Edition and IEC 664 respectively.

This instrument has autoranging line voltage input. Be sure the supply

voltage is within the specified range.
The Mains wiring and connectors shall be compatible with the connector

used in the premise electrical system. Failure, to ensure adequate earth

grounding by not using the correct components may cause product

damage, and serious injury.

Always use the three-prong AC power cord supplied with this product.

Failure to ensure adequate earth grounding by not using this cord can

cause product damage.

Содержание NFA X-Series




































































































Результаты поиска

Содержание NFA X-Series

Отзывы:

Бренды по названию

Популярные бренды

Keysight Technologies NFA X-Series, Руководство по началу работы и устранению неисправностей

Результаты поиска

Содержание NFA X-Series

Отзывы:

Бренды по названию

Популярные бренды