Keysight Technologies N9030B Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 33

background image

4

Installation Note N9030-90077

Option BBA, Analog Baseband I/Q Inputs Upgrade Kit

Introduction

This kit provides all parts and instructions necessary to install Option BBA, Analog Baseband I/Q
Input, into the Keysight N9030B with frequency range 26.5 GHz and below.

1.

This upgrade kit is

not compatible

with N9030B PXA signal analyzers with any

of the following options currently installed:

N9030B-B5X - 510 MHz Analysis Bandwidth
N9030B-544 - Frequency Range, 3 Hz to 44 GHz
N9030B-550 - Frequency Range, 3 Hz to 50 GHz

2.

This upgrade kit installation requires that you re-install instrument software.
The latest revision of the PXA Signal Analyzer software may be downloaded

from

http:/www.keysight.com/find/xseries_software

The instrument software must be installed AFTER the hardware in the kit is

installed. Follow the procedure in this document for redeeming and installing

the option upgrade license key.

3.

The option is licensed for one instrument model/serial number combination.

The license key will only install on the designated instrument.

«
...
2
3
4
5
6
...
»

Содержание N9030B


































Отзывы:

Нет отзывов

Похожие инструкции для N9030B

Бренд: Kawai Страницы: 70

Бренд: OHAUS Страницы: 52

Бренд: SAGEMCOM Страницы: 33

Ultraprobe 9000

Бренд: UE Systems Страницы: 25

ULTRAPROBE 10000

Бренд: UE Systems Страницы: 6

CP-4900 Micro-GC

Бренд: Varian Страницы: 13

Бренд: Jula Страницы: 9

LISST-PORTABLE XR

Бренд: Sequoia Страницы: 41

Бренд: RIDGID Страницы: 18

SF6 Portable Monitor

Бренд: Bacharach Страницы: 2

Бренд: Magnescale Страницы: 2

Бренд: Datakom Страницы: 27

LiveTester LT 220

Бренд: StarLogixs Страницы: 7

Бренд: 3M Страницы: 168

Бренд: ICP DAS USA Страницы: 4

Бренд: G4M Страницы: 52

83620B 8360 Series

Бренд: Agilent Technologies Страницы: 2

Бренд: Cressi Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды