Keysight Technologies N774 C Series Скачать руководство пользователя

Страница: 58 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

User Interface Reference

Big Num

If you are only interested in the measured numbers and not in the

graphical view, you may exit the graph by clicking on the

Big Num

option.

This option hides the graph and only the big sized measured numbers are

displayed on the

Control Instrument

page.

How to Measure Power

The Power Value

For each port, the optical power is measured and returned or displayed.

The power reading represents the average optical power over the selected

averaging time. The power meter can continuously self-trigger new

measurements or be configured to wait for external software or hardware

triggers.

How to Set the Power Unit

The Power Unit setting allows you to select either W, dBm or dB as the

units in which power is displayed or returned. For returning large amounts

of logged data, the fastest data transfer is achieved using W units.

What are the Power Units?

The SI unit for power measurement is Watt (W).

You can also measure power in dB or dBm. Values returned in these units

are derived from measurement in Watts.

By selecting dBm, the following calculation is made:

Where,

dBm

is the power value returned in dBm, and

input

is the input signal level in Watts.

Power, in units of dBm, is measured relative to 1 mW. It is an absolute

power measurement.

Power, in units of dB, is measured relative to a particular reference power

value.

The following calculation is made:

Содержание N774 C Series





















































































Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды

Keysight Technologies N774 C Series, Руководство пользователя

Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды