Keysight Technologies N7020A Скачать руководство пользователя страница 57

Страница: 57 / 92

Keysight N7020A and N7024A Power Rail Probes

User’s Guide

6 Calibrating

N7020A / N7024A Probe’s DC Attenuation/Offset Calibration Using N7022A Main Cable

N7020A / N7024A Probe’s DC Attenuation/Offset Calibration Using N7023A Probe

Browser

Always calibrate the probe before making any critical measurements. A probe

calibration removes attenuation errors, offset errors, and timing delays that are

introduced by the probe. This chapter contains basic calibration procedures for

the supported Infiniium oscilloscopes. For additional information on the probe

calibration, refer to the oscilloscope’s user documentation.

The following calibrations are described in this chapter:
• N7020A / N7024A Probe’s DC Attenuation/Offset Calibration Using N7022A

Main Cable

•

N7020A / N7024A Probe’s DC Attenuation/Offset Calibration Using N7023A

Power Rail Probe Browser

CAUTION

Always wear an ESD wrist strap when working with active probes. Not doing so can result

in the probe becoming permanently damaged.

Содержание N7020A





























































































Результаты поиска

Содержание N7020A

Отзывы:

Бренды по названию

Популярные бренды

Keysight Technologies N7020A, Руководство пользователя

Результаты поиска

Содержание N7020A

Отзывы:

Бренды по названию

Популярные бренды