Keysight Technologies N5252A Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 62

background image

Regulatory Information

EMC

This product has been designed and tested in accordance with accepted industry
standards, and has been supplied in a safe condition. The documentation contains
information and warnings that must be followed by the user to ensure safe
operation and to maintain the product in a safe condition.
Complies with the essential requirements of the European EMC Directive as well as
current editions of the following standards (dates and editions are cited in the
Declaration of Conformity):
— IEC/EN 61326-1
— CISPR Pub 11 Group 1, class A

Caution: This equipment is not intended for use in residential environments and

     may not provide adequate protection to radio reception in such environments.
—  AS/NZS CISPR 11
—  CAN ICES/NMB-001(A)

This ISM device complies with Canadian ICES-001.

Cet appareil ISM est conforme a la norme NMB-001 du Canada.

Declaration of Conformity): IEC/EN 61010-1
Acoustic statement (European Machinery Directive)

—  Acoustic noise emission
—  LpA <70 dB
—  Operator position
—  Normal operation mode per ISO 7779

Declaration of Conformity

A declaration of conformity is available upon request, or a copy is available on the
Keysight Technologies web site at

https://regulations.about.keysight.com/DoC/

South Korean Class A EMC Declaration

※

This EMC statement applies to the equipment only for use in a business environment.

사 용

자

안

내

문

이 기기는

업무용

환경에서

사용할

목적으로

적합성평가를

받은

기기로서

가정용

환경에서

사용하는

경우

전파간섭의

우려가

있습니다

.

※

사용자

안내문은

“

업무용

방송통신기자재

”

에만

적용한다

.

Complies with the following standard (dates and editions are cited in the

If there is a "KC" mark on the instrument, then the following statement applies:
This equipment has been conformity assessed for use in business environments.

In a residential environment, this equipment may cause radio interference.

This is a sensitive measurement apparatus by design and may have some performance loss when
exposed to ambient continuous electromagnetic phenomenon similar to those used in testing per
IEC 61000-4-6 (3V). This occurs when the frequency of the external phenomenon is within the
extenders Measure IF output frequency of approximately 4

MHz

or 13 MHz

. Noise floor degrades

up to

5

0

dB. Dynamic range, stability and trace noise will also be affected. The operating

environment should be shielded from this frequency interference for best performance.

Safety

60

N5252-90002 User's Guide

«
...
58
59
60
61
62
»

Содержание N5252A































































Отзывы:

Нет отзывов

Похожие инструкции для N5252A

Бренд: TA Страницы: 58

Бренд: WattNode Страницы: 57

Бренд: Kanomax Страницы: 31

Бренд: Hach Страницы: 196

Бренд: TA Instruments Страницы: 7

Бренд: HANSA-FLEX Страницы: 23

Бренд: JENCO Страницы: 13

Бренд: OHAUS Страницы: 71

Бренд: NCS Страницы: 7

Бренд: Ferret Страницы: 18

LaserDIMENSIONMASTER 3336

Бренд: Calculated Industries Страницы: 2

Бренд: Vega Страницы: 24

Бренд: Anritsu Страницы: 15

Бренд: MONARCH INSTRUMENT Страницы: 28

Бренд: STM Страницы: 31

Бренд: DAPAudio Страницы: 8

Celviano AP-500

Бренд: Casio Страницы: 2

Бренд: KATA Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды