Keysight Technologies N5221B Скачать руководство пользователя страница 5

Страница: 5 / 88

Installation Note N5222-90131

Description of the Upgrade
Getting Prepared

Getting Prepared

To successfully install this upgrade kit, you will need the following:
— A license key - refer to

“License Key Redemption”

below.

— A PDF copy or a paper copy of the PNA Service Guide - refer to

“Downloading the Online PNA Service Guide”

below.

— An ESD-safe work area - refer to

“Protecting Your Workspace from

Electrostatic Discharge”

below.

— Correct tools - refer to

“Tools Required for the Installation” on page 9

— Enough time - refer to

“About Installing the Upgrade” on page 10

— Test equipment for the post-upgrade adjustments and full instrument

calibration. To view the equipment list, click the Chapter 3 bookmark “Tests
and Adjustments” in the PDF Service Guide

The PNA contains extremely sensitive components that can be ruined if

mishandled. Follow instructions carefully when making cable connections,

especially wire harness connections.
The person performing the work accepts responsibility for the full cost of

the repair or replacement of damaged components.

IMPORTANT!

—

This document contains references to legacy and to a new A25

HMA26.5 Multiplier/Amplifier assembly. Your model instrument may

have a legacy HMA26.5 or a new HMA26.5 assembly. Both types of

assemblies are compatible with this upgrade. This note is for your

reference, because some figures contain legacy assemblies that your

instrument may not have installed.

—

If you want to verify your instrument’s A25 HMA26.5

Multiplier/Amplifier, refer to

“Verify the Model/Version of HMA26.5

Installed” on page 7

—

See also, your instrument’s PDF Service Guide

a. See

“Downloading the Online PNA Service Guide” on page 8

1. See

“Downloading the Online PNA Service Guide” on page 8

Содержание N5221B

























































































Результаты поиска

Содержание N5221B

Отзывы:

Похожие инструкции для N5221B

Бренды по названию

Популярные бренды

Keysight Technologies N5221B, Руководство пользователя

Результаты поиска

Содержание N5221B

Отзывы:

Похожие инструкции для N5221B

Бренды по названию

Популярные бренды