Keysight Technologies N5221B Скачать руководство пользователя страница 14

Страница: 14 / 88

14 Installation Note N5222-90131

Description of the Upgrade
Items Included in the Upgrade Kit

W90

A43 port 3 receiver attenuator to A24 mixer brick (C)

N5222-20006

W91

Port 4 RCVR D IN to A44 port 4 receiver attenuator

N5222-20022

W92

A44 port 4 receiver attenuator to A24 mixer brick (D)

N5222-20026

W162

RF cable, assembly FP, A29

port 1 test coupler to A71 port 1 Bias combiner

N5222-20115

W163

RF cable, assembly FP, Port 3 CPLR THRU to A72 port 3 Bias combiner

N5222-20121

W164

RF cable, assembly FP, A30 Port 3 test coupler to A72 port 3 bias combiner

N5222-20117

W165

RF cable, assembly FP, Port 4 CPLR THRU to A73 port 4 Bias combiner

N5222-20122

W166

RF cable, assembly FP, A31

port 4 test port coupler to A73 port 4 Bias combiner

N5222-20118

W168

RF cable, assembly FP, A31

port 4 test port coupler to A73 port 4 Bias combiner

N5222-20116

W168

Cable assembly, RF CA, A70 LFE board to Source 2

N5242-60079

W175

A72 bias combiner "RF IN" to conn "Port3" on LFE board

N5240-60098

W176

A73 bias combiner "RF IN" to conn "Port4" on LFE board

W202

RF cable, A24 mixer brick (top connector) to A21 HMA25.6 A24 mixer brick (top

connector)

N5222-20126

Ribbon cable, A19 test set motherboard J206 to A43 port 3 receiver attenuator

8121-0982

Ribbon cable, A19 test set motherboard J207 to A44 port 4 receiver attenuator

8121-0982

Ribbon cable, A19 test set motherboard J213 to A24 mixer brick (2)

N5242-60006

Ribbon cable, A19 test set motherboard J202 to A35 port 3 source attenuator

N5242-60008

Ribbon cable, A19 test set motherboard J203 to A36 port 4 source attenuator

N5242-60008

Cable, DC, 2–pin to R/A SMP (Port 3 bias combiner DC to A19 Bias J543 and Port 4

bias combiner DC to A19 Bias J544.)

N5240-60091

a. The A22 splitter (

5087-7139) and

N5222-20007, N5222-20008, and N5222-20009 cables are only used with a legacy

HMA26.5 p/n: 5087-7765. If your PNA has a new N5240-60101 assembly installed, then set aside these parts as spares for

use in other PNAs with the older HMA26.5 or discard. If you are unclear which HMA26.5 assembly your PNA has installed, refer

Figure 1 on page 7

b. The N5222-20126 cable is used only with instruments that have a newer HMA26.5 installed. If your PNA has a legacy

5087-7765 HMA26.5 assembly installed, then this cable can be discarded. If you are unclear which HMA26.5 assembly your

PNA has installed, refer to

Figure 1 on page 7

Extra quantities of items such as protective plastic caps, screws, cable ties,

and cable clamps may be included in this upgrade kit. It is normal for some

of these items to remain unused after the upgrade is completed.

Table 2

Contents of Upgrade Kit N5222-60131

Ref

Desig.

Description

Qty

Part Number

Содержание N5221B

























































































Результаты поиска

Содержание N5221B

Отзывы:

Похожие инструкции для N5221B

Бренды по названию

Популярные бренды

Keysight Technologies N5221B, Руководство пользователя

Результаты поиска

Содержание N5221B

Отзывы:

Похожие инструкции для N5221B

Бренды по названию

Популярные бренды