Keysight Technologies N4917CPCA Скачать руководство пользователя страница 46

Страница: 46 / 84

Keysight N4917CPCA Optical Receiver Stress Test for CPRI Fronthaul Networks User Guide

Using the N4917CPCA Software

Note the set of values for De-emphasis. You must also enter these values

into the respective Eye Parameter files. Refer to the “

Stressed Eye

Calibration

” section for more information on Parameter Files.

Figure 12

System Performance Check window

To measure the basic system performance click the

Start

button under

Intrinsic Meas

. This initiates a sequence of tests with all jitter/impairment

sources turned off, and measures extinction ratio (ER), optical modulation

amplitude (OMA), vertical eye closure penalty (VECP), jitter J2, and jitter

J9. The results of this clean optical signal are displayed in the first column

of the table. The other columns,

Lower Limit

and

Upper Limit

are not hard

limits; they are just a typical range of values that might be expected.

Results above or below these limits might still be acceptable.

Figure 13

shows the results of a System Performance Check. Results are

highlighted if the measured value falls outside of the lower/upper limits, as

a warning only. In addition to checking whether the measured results fall

within the limits, there is also a check on the amount of margin to the

stressed eye specification for J2 and J9. For best performance and

likelihood of achieving a successful stressed eye calibration there should

be more margin for the J9 results than the J2 results, since the J9

parameter is most sensitive to the addition of the other eye impairments.

Содержание N4917CPCA





















































































Результаты поиска

Содержание N4917CPCA

Отзывы:

Похожие инструкции для N4917CPCA

Бренды по названию

Популярные бренды

Keysight Technologies N4917CPCA, Руководство пользователя

Результаты поиска

Содержание N4917CPCA

Отзывы:

Похожие инструкции для N4917CPCA

Бренды по названию

Популярные бренды