Keysight Technologies M8131A Скачать руководство пользователя страница 109

Страница: 109 / 158

Keysight M8131A 16/32 GSa/s Digitizer User’s Guide

109

Remote Programming

<filter_values> The set of 49 coefficients as comma separated ASCII list or

binary block of doubles. Each coefficient is in the range [-2;+2]. The

frequency response of the correction filter is not allowed to exceed a gain

of 2.0 over the entire frequency range.

Query

:CHANnel<N>:DPRocessing:FILTer[:VALue]? [{S16G | S32G}]

The query returns the current coefficients for the correction filter for the

specified channel. If the optional parameter of sample rate mode is given,

it returns the filter values for the specified sample rate otherwise for the

current sample rate mode.

Returned Format

:[:CHANnel<N>:DPRocessing:FILTer[:VALue]] <filter_values> <NL>

:CHANnel<N>:DPRocessing:FILTer:DEFault

Command

:CHANnel<N>:DPRocessing:FILTer:DEFault [{S16G |
S32G}]

Description

The command sets the default values for the 49 correction filter

coefficients for the specified channel. If the optional parameter of sample

rate mode is given, it sets the default filter values for the specified sample

rate otherwise for the current sample rate mode.

<N> An integer, 1-4 in a single digitizer system.

S16G Selects the coefficients for 16GSa/s

S32G Selects the coefficients for 32GSa/s

Query

:CHANnel<N>:DPRocessing:FILTer:DEFault? [{S16G | S32G}]

The query returns the default values for the coefficients for the correction

filter for the specified channel. If the optional parameter of sample rate

mode is given, it returns the default filter values for the specified sample

rate otherwise for the current sample rate mode.

Returned Format

[:CHANnel<N>:DPRocessing:FILTer:DEFault] <filter_values> <NL>

Содержание M8131A































































































































































Результаты поиска

Содержание M8131A

Отзывы:

Похожие инструкции для M8131A

Бренды по названию

Популярные бренды

Keysight Technologies M8131A, Руководство пользователя

Результаты поиска

Содержание M8131A

Отзывы:

Похожие инструкции для M8131A

Бренды по названию

Популярные бренды