Keysight Technologies AC6801B Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 197

background image

SYSTem Subsystem

The SYSTem subsystem controls instrument functions that are not directly related to output control,
measurement, or status functions. Note that IEEE-488 Common commands also control system
functions such as state management.

SYSTem:BEEPer[:IMMediate]

Issues a single beep.

Parameter

Typical Return

(none)

(none)

Issue a single beep: SYST:BEEP

This command overrides the current beeper state . You can issue a beep even if the beeper is turned
off by

SYSTem:BEEPer:STATe

.

Programmed beeps may be useful for program development and troubleshooting.

SYSTem:BEEPer:KCLick ON|1|OFF|0
SYSTem:BEEPer:KCLick?

Disables or enables the click tone heard when you press a front-panel key.

Parameter

Typical Return

ON|1|OFF|0

0 (OFF) or 1 (ON)

Disable front-panel key click: SYST:BEEP:KCLick OFF

The front-panel key click and instrument beeper settings do not affect each other.

This parameter is not affected by

or

.

SYSTem:BEEPer:STATe ON|1|OFF|0
SYSTem:BEEPer:STATe?

Disables or enables the beep heard when an error is generated.

Parameter

Typical Return

ON|1|OFF|0

0 (OFF) or 1 (ON)

Disable the beeper state: SYST:BEEP:STAT OFF

The front-panel key click and instrument beeper settings do not affect each other.

A beep is always emitted (even with beep state OFF) when

is sent.

This parameter is not affected by

or

.

Keysight AC6800B Series Operating and Service Guide

151

3 SCPI Programming Reference

«
...
149
150
151
152
153
...
»

Содержание AC6801B






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AC6801B

Бренд: Sven Страницы: 4

Бренд: AEM Performance Electronics Страницы: 9

WB-800VPS-IPVM-12

Бренд: WattBox Страницы: 16

Бренд: Vertiv Страницы: 17

Бренд: LDR Страницы: 32

APT 7000 Series

Бренд: Cal Power Страницы: 8

Бренд: PANCONNECT Страницы: 2

Бренд: Ametek Страницы: 90

Бренд: Ametek Страницы: 114

Бренд: ABB Страницы: 1016

Бренд: Panamax Страницы: 2

unimes H U-PW powerway

Бренд: hager Страницы: 82

Бренд: Ayre Страницы: 2

Бренд: Powerfix Profi Страницы: 44

Бренд: LIGHTNING PROTECTION INTERNATIONAL PTY LTD Страницы: 52

MVPS1000 Series

Бренд: FiDUS Страницы: 6

Бренд: FiDUS Страницы: 6

Бренд: EV-OPTIMIZER Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды