Keysight Technologies 85058V Скачать руководство пользователя страница 49

Страница: 49 / 58

85058V

6-3

Replaceable Parts

Copying Replacement Device Verification Data to the Original Verification Data Media

Copying Replacement Device Verification Data to the Original

Verification Data Media

IMPORTANT

The information in the following two processes applies only to writable USB

drives. If the USB drive shipped with your verification kit or replacement device

has either the Keysight or Keysight logo on it, it is read-only, and the following two

processes do not apply. If this is the case, simply use the USB drive that was

shipped with your replacement device when you connect that device during the

system verification process.

This section describes how to copy the new replacement device verification data from the USB

drive provided with the device, to the verification data media (floppy disk or USB) included with

the original verification kit. Please be aware that once you write over the “old” data, the data

cannot be recovered. Therefore, it is highly recommended that you follow the procedure below

in “Old Verification Device Data – Backup Process” to make a backup copy of the “old”

verification data BEFORE you perform the “New Verification Device Data -Transfer Process”

procedure. Be sure to keep the new USB drive. It will be your backup copy of the new

replacement device verification data.

NOTE

This procedure assumes you have access to a PC or a PNA to perform these

tasks.

Old Verification Device Data – Backup Process

1. Insert the old verification device data media (floppy disk or USB) into your computer or PNA

and view the contents with Windows Explorer.

2. Copy all of the files to the clipboard.
3. Remove the old verification device data media (floppy disk or USB) from your computer or

PNA.

4. Insert the new USB drive into your computer or PNA and view the contents with Windows

Explorer.

5. Create a new directory on the new USB drive and name it using the format

Model_Serial_YYYYMMDD. Use your kit’s model number, serial number, and the current

date. Example: 85055A_2815A01234_20120827.

6. Open the new directory you created in the previous step and paste the files from the

clipboard.



All of the files (nine files: one .txt file, four .dat files, and four .unc files) you copied from the

old verification device data media should be present. You now have a complete backup of

the old verification device data on the new USB drive.

Содержание 85058V



























































Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды

Keysight Technologies 85058V, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды