Page 22
KD-MSW8x4Pro Operating Instructions
Page 21
10. Volume Level Set:
'ccVxzz'
x = output select [1~4]
zz = 2-digit volume select [00~30]
cc = the 2-digit unit address [01~15] or 'CC'
Note: Audio volume control is supported in Component mode only. See Video Type Set..
Example:
To set the volume of output 2 of the unit at address 10 to value of -12 dB, issue the following
RS-232 sequence: '10V209' or '10v209'
11.
Factory Default Reset:
'ccF0'
This command causes the unit to be reset to the factory default configuration.
Example:
To reset the unit at address 02 to factory default configuration, issue the following RS-232
sequence: '02F0' or '02f0'
To reset the stand-alone unit to factory default configuration, issue the following RS-232
sequence: 'CCF0' or 'CCf0'
Item
Default Value
Selected Input for every output
1
Distribution Amplifier Mode
Enabled (Input = 1)
Unit address
16 (stand-alone)
Fade-to-Black Interval
6
Volume 15
Output mode
Component
Front panel pushbuttons
Enabled
IR Control
Enabled
zz
Volume (dB)
00
mute
01
-28
02
-26
03
-24
04
-22
05
-20
06
-18
07
-16
08
-14
09
-12
zz
Volume (dB)
10
-10
11
-8
12
-6
13
-4
14
-2
15
0 (default)
16
+2
17
+4
18
+6
19
+8
zz
Volume (dB)
20
+10
21
+12
22
+14
23
+16
24
+18
25
+20
26
+22
27
+24
28
+26
29
+28
30
+30
KD-MSW8x4Pro Operating Instructions
5.
Video Type Set:
'ccOR' : RGBHV mode
'ccOC' : Component mode (factory default)
cc = the 2-digit unit address [01~15] or 'CC'
Example:
To set video type to RGBHV for a stand-alone unit, issue the following RS-232 sequence:
'CCOR' or 'CCor' or 'CCoR' or 'CCOr'
To set video type to Component for a unit at address 01, issue the following RS-232 sequence:
'01OC' or '01oc' or '01oC' or '01Oc'
6.
IR Control Set:
'L': Disable IR/Wired IR Remote Control functionality
'U': Enable IR/Wired IR Remote Control functionality
This command is not addressable.
Example:
To disable the IR control of a unit issue the following RS-232 command: 'L' or ' l '
To enable the IR control of a unit, issue the following RS-232 command: 'U' or 'u'
7.
Front Panel Control Set:
'D': Disable front panel pushbutton controls
'E': Enable front panel pushbutton controls
This command is not addressable.
Example:
To disable the pushbuttons of a unit, issue the following RS-232 command: 'D' or 'd '
To enable the pushbuttons of a unit, issue the following RS-232 command: 'E' or 'e'
8.
Distribution Amplifier Mode Set:
'Zn', where n is input select [1~8]
'Z0' - restore the previous input/output configuration
This command switches all outputs to a selected input.
Note: For Fat Boy Series expansion, ALL outputs follow the selected input
Example:
To switch all outputs of ALL units, irrespectively of address, to input 6,
issue the following RS-232 sequence: 'Z6'
To restore the previous I/O configuration of ALL units irrespectively of address,
issue the following RS-232 sequence: 'Z0'
9.
Power Control:
S : Power OFF
Q : Power ON
Note: This command is not addressable.
Example:
To turn the power ON issue the following RS-232 command: 'q' or 'Q'
To turn the power OFF issue the following RS-232 command: 's' or 'S'
KDMSW8x4Pro_Manual.qxd 1/17/07 4:33 PM Page 21
