manualshive.com logo in svg

Kewtech KT63 PLUS, Руководство по эксплуатации

Поделиться
Скачать
Kewtech KT63 PLUS Скачать руководство пользователя страница 16

kewtechcorp.com

16

Polarity Test Pad

In No-trip mode the tester can be used with the mains lead KAMP12 
when testing at 13A socket outlets, or the distribution board lead 
set ACC063 for testing at other points in the circuit. In No-trip mode 
the 3 colour coded prods/crocodile clips of the test lead should be 
connected to the corresponding Line, Neutral and Earth terminals.

 

Your Kewtech KT63 PLUS tester has a special polarity test function.

It is a little known fact that a system can be reverse 
wired with Live (Phase) to earth/neutral and earth/
neutral to Live (Phase) The sockets will all work and 
conventional loop testers will show and test that 
everything is correct despite this very dangerous wiring 
condition.
Although extremely rare, this dangerous condition can 
exist so if your test shows this fault do not proceed - if 
in any doubt advise your customer to contact their 
supply company immediately.
Touch the touchpad area next to the test button. There 
should be no change in the indication given. If the 
Voltage/Polarity LED flashes Red and a warning tone 
is emitted when the touchpad is touched a potentially 
dangerous polarity reversal exists. Do not proceed. If in 
any doubt advise the customer to contact the electricity 
supply company immediately.

Содержание KT63 PLUS

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды