manualshive.com logo in svg

Kewtech KT41, Инструкция по эксплуатации

Поделиться
Скачать
Kewtech KT41 Скачать руководство пользователя страница 16

14

5

Operating Instructions

5.1  Initial Checks: to be carried out before any testing;

Always inspect your test instrument and lead accessories 
for abnormality or damage-

If abnormal conditions exist DO NOT PROCEED WITH 
TESTING. Have the instrument checked by Kewtech.

Before pressing the test button, always check the LED's for
the following sequence:

P-E Green LED must be ON

P-N Green LED must be ON

Red LED must be OFF

If the above sequence is NOT displayed or the RED LED is
on for any reason, DO NOT PROCEED AS THERE IS 
INCORRECT WIRING. The cause of the fault must be
investigated and rectified.

Voltage Measurement

When the instrument is first connected to the system, it 
will display the phase-earth voltage which is updated every 
1s. This mode is cancelled the first time the test button is 
pressed. If this voltage is not normal or as expected, DO 
NOT PROCEED.

NOTE: This is a single phase (230V AC) instrument and 

under no circumstances

should it be connected to 2-

phases or a voltage exceeding 10%-15%.

If the input voltage is greater than 260V the display will 
indicate ‘VP-E Hi’ and Loop or PSC measurements can not 
be made even if the Test button is pressed.

5.2 Measurement of Loop impedance

a.  Loop Impedance at Mains Socket Outlet

Select the 20

Ω

, 200

Ω

or 2000

Ω

range as desired

Содержание KT41
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды