KERN OPTICS OKO 178 Скачать руководство пользователя

Страница: 28 / 29

OKO-1-BA-en-2111

Problem

Possible causes

Blurred details

Bad picture

Poor contrast

Vignetted field of view

Aperture diaphragm is not open wide enough

Condenser is lowered too far
The objective does not belong to this

microscope
The front lens of the lens is dirty
An immersion lens is used without immersion

oil
The immersion oil contains air bubbles

The condenser is not centered

The recommended immersion oil is not used

Dirt / dust on the lens

Dirt / dust on the front lens of the condenser

Dirt or dust in the field of view

Dirt / dust on the eyepieces
Dirt / dust on the front lens of the

Condenser
Dirt / dust on the object

One side of the image is blurred

The table was not mounted correctly
The lens is not correctly pivoted to the beam

path

The revolving nosepiece is not mounted

correctly
The object lies with the upper side down.

The picture flickers

The revolving nosepiece is not correct

mounted

The lens is not properly mounted on

slewed into the beam path

The condenser was not properly

centered

The coarse drive is difficult to

rotate

The rotational resistance brake is too

tightened firmly

The cross table is

Solid blocked.

The table moves down by itself

The fine drive adjusts itself

The rotational resistance brake is too little

tightened

Touching the table blurs the image

The table was not mounted correctly

Содержание OPTICS OKO 178






























Результаты поиска

Содержание OPTICS OKO 178

Отзывы:

Похожие инструкции для OPTICS OKO 178

Бренды по названию

Популярные бренды

KERN OPTICS OKO 178, Руководство по эксплуатации

Результаты поиска

Содержание OPTICS OKO 178

Отзывы:

Похожие инструкции для OPTICS OKO 178

Бренды по названию

Популярные бренды