Kenwood TK-3701D-E Скачать руководство пользователя страница 5

Страница: 5 / 31

INSTALLING THE BELT CLIP

If necessary, attach the belt clip using the two

supplied M3 x 8 mm binding screws.

Note:

◆

If the belt clip is not installed, its mounting location

may get hot during continuous transmission or when

left sitting in a hot environment.

◆

Use the Phillips #2 screwdriver.

Belt clip

M3 x 8 mm

screws

CAUTION

◆

Do not use glue which is designed to prevent screw loosening when installing the belt

clip, as it may cause damage to the transceiver. Acrylic ester, which is contained in

these glues, may crack the transceiver’s back panel.

INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE

JACKS

Note:

◆

For the speaker/ microphone jack, waterproof performance is guaranteed by securing

the supplied cap. Waterproof performance will not be guaranteed by connecting an

optional speaker/ microphone, etc.

◆

Use the Phillips #1 screwdriver.

If you are not using an optional speaker/ microphone

or headset, install the cap over the speaker/

microphone jacks.

Secure the cap in place using the attached screw.

Speaker/ microphone

jack cap

Screw

Содержание TK-3701D-E
































Результаты поиска

Содержание TK-3701D-E

Отзывы:

Похожие инструкции для TK-3701D-E

Бренды по названию

Популярные бренды

Kenwood TK-3701D-E, Руководство пользователя

Результаты поиска

Содержание TK-3701D-E

Отзывы:

Похожие инструкции для TK-3701D-E

Бренды по названию

Популярные бренды