Kenwood TK-3701D-E Скачать руководство пользователя страница 4

Страница: 4 / 31

CHARGING THE BATTERY PACK

ATTENTION:

◆

Always switch OFF a transceiver equipped with a battery pack before inserting the

transceiver into the charger.

Plug the AC adapter cable into the jack located on the rear of the charger.

Plug the AC adapter into an AC outlet.

Slide a battery pack or a transceiver equipped with a battery pack into the

charging slot of the charger.

• Make sure the metal contacts of the battery pack mate securely with the

charger terminals.

• The indicator lights red and charging begins.

Indicator

When charging is completed, the indicator flashing green. Remove the battery

pack or the transceiver from the charging slot of the charger.

• It takes approximately 3 hours to charge the battery pack.

• When the charger will not be used for a long time, unplug the AC adapter

from the AC outlet.

Note:

◆

When the indicator blinks red, the battery pack is either defective or the battery pack

contacts are not properly mated with those of the charger.

◆

When the indicator flashes green and orange, the battery pack has not satisfied the

charging start temperature. Remove the battery pack from the charger and wait until it

reaches a normal temperature before charging it again.

◆

The ambient temperature should be between 5°C and 40°C while charging is in

progress. Charging outside this range may not fully charge the battery.

◆

The battery pack life is over when its operating time decreases even though it is fully

and correctly charged. Replace the battery pack.

Содержание TK-3701D-E
































Результаты поиска

Содержание TK-3701D-E

Отзывы:

Похожие инструкции для TK-3701D-E

Бренды по названию

Популярные бренды

Kenwood TK-3701D-E, Руководство пользователя

Результаты поиска

Содержание TK-3701D-E

Отзывы:

Похожие инструкции для TK-3701D-E

Бренды по названию

Популярные бренды