manualshive.com logo in svg

Kenwood NX-5000 series, Руководство пользователя

Kenwood NX-5000 series - профессиональные портативные радиостанции с широким диапазоном частот и возможностью работы в цифровом и аналоговом режимах. Получите бесплатный руководство пользователя для вашего удобства на manualshive.com. Наслаждайтесь передовой технологией без лишних затрат.

Поделиться
Скачать
background image

About the behavior of the transceiver when sending an Individual Call

The transceiver behaves as follows depending on the response message from the system after initiating an Individual Call
in a P25 Trunking system:

Table 2-8 Behavior of the Transceiver When Sending an Individual Call

Status

Transceiver Behavior

When a rejection

response message is

received from the

target transceiver

The Call Deny Tone (3 beeps) sounds from the transceiver, and “Call Deny” appears on the display

for 1 sec. Then, the transceiver restores the channel display and the Individual Call ends. If

Incoming Reset Time of the transmitting transceiver elapses and the call ends, the behavior of the

transceiver is also the same.

When no response is

received from the

target transceiver

If the other party does not respond even if the time configured in Initiating Reset Timer expires,

No reply Tone (4 beeps) sounds from the transceiver, and “No reply” appears on the display for

1 sec. Then, the transceiver restores the channel display and the Individual Call ends.

When the transceiver

receives a response

message indicating the

queue state from the

system

The Call Queue Tone (2 beeps) sounds from the transceiver, “Queued” appears on the display,

and the transceiver enters the standby state.

When the transceiver

receives a service

invalid message from

the system

The Call Invalid Tone (4 beeps) sounds from the transceiver, and “System Deny” appears on the

display for 1 sec. Then, the transceiver restores the channel display and the Individual Call ends.

When the transceiver

does not receive any

messages from the

system

The Call Fail Tone (2 beeps) sounds from the transceiver, and “Fail” appears on the display for 1

sec. Then, the transceiver restores the channel display and the Individual Call ends.

Configuration using KPG-D1/ D1N

0

Assigning functions to the 

PF

 keys on the transceiver (

 Transceiver Settings > Key Assignment)

0

Configuring 

Manual Dialing

 to be enabled or disabled (

 Transceiver Settings > Personal > Personal Features >

P25 Trunking > General)

0

Configuring 

Call in Progress Tone

 to be enabled or disabled (

 Transceiver Settings > P25 > P25 Information >

Trunking)

0

Configuring 

Disconnect Indication Tone

 to be enabled or disabled (

 Transceiver Settings > P25 > P25

Information > Trunking)

Receiving an Individual Call

If the received Individual ID matches the Individual ID configured for the transceiver, the transceiver can receive the Individual Call.
Depending on the configuration in KPG-D1/ D1N and system configuration, the transceiver receives an Individual Call in

the following states:

0

Automatic Response (KPG-D1/ D1N configuration)

If 

Automatic Response

 is enabled, and when the receiving transceiver receives from the system a message requesting

reception, the transceiver automatically sends an acknowledgment and can initiate an Individual Call.
If 

Automatic Response

 is disabled, and when the receiving transceiver receives from the system a message requesting

reception, the transceiver can initiate an Individual Call by pressing the 

PTT

 switch or 

Call Response

 key to send an

acknowledgment.

0

Availability Check (system configuration)

The transmitting transceiver sends a message requesting an Individual Call to a system when initiating an Individual

Call, and the system sends a message requesting an acknowledgment to the receiving transceiver to confirm the

availability of the receiving transceiver.
The transmitting transceiver sends a message requesting connection to the system, and the system sends a message

for traffic channel assignment if the system allows this request. When the transceiver receives this message, the

transceiver automatically migrates to a traffic channel, and then the transceiver will emit the received audio on a traffic

channel.

2 P25 TRUNKING SYSTEM

2.6 Making an Individual Call

P25 FUNC (K)/Ver 2.20

93

CONTENTS

INDEX

Содержание NX-5000 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX-5000 series

GE AquaTrans AT868 Abridged Manual preview
AquaTrans AT868
Бренд: GE Страницы: 67
PAG 6001 Quick Start Manual preview
6001
Бренд: PAG Страницы: 2
JETStream JT220M User Manual preview
JT220M
Бренд: JETStream Страницы: 19
Alinco EC10 s Specifications preview
EC10 s
Бренд: Alinco Страницы: 4
aci WPR2 Series Installation & Operation Instructions preview
WPR2 Series
Бренд: aci Страницы: 8
aci Room Series Installation & Operation Instructions preview
Room Series
Бренд: aci Страницы: 4
Audiovox Pursuit PRO-OE3B3 Programming Manual preview
Pursuit PRO-OE3B3
Бренд: Audiovox Страницы: 4
HBK AED 9101D Quick Start Manual preview
AED 9101D
Бренд: HBK Страницы: 40
HBK AED 9101D Operating Manual preview
AED 9101D
Бренд: HBK Страницы: 104
emitor Satlook Micro G2 User Manual preview
Satlook Micro G2
Бренд: emitor Страницы: 24
CAME RE432 Quick Start Manual preview
RE432
Бренд: CAME Страницы: 2
GES AudioTroll 9400 Operating & Installation Manual preview
AudioTroll 9400
Бренд: GES Страницы: 13
Sagem DTR94 HD FREESAT User Manual preview
DTR94 HD FREESAT
Бренд: Sagem Страницы: 48
Yaesu FT-912R Operating Manual preview
FT-912R
Бренд: Yaesu Страницы: 45
Continental Automotive TXN2 User Manual preview
TXN2
Бренд: Continental Automotive Страницы: 8
Topfield TBF-7300 Quick Manual preview
TBF-7300
Бренд: Topfield Страницы: 16
PS Engineering PAR100EX System Installation And Operation Manual preview
PAR100EX
Бренд: PS Engineering Страницы: 40
Xantech Dinky Link DL95M Installation Instructions preview
Dinky Link DL95M
Бренд: Xantech Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды