Kenwood KDC-MP243 Скачать руководство пользователя

Страница: 17 / 20

English

Connecting Wires to Terminals

Battery

Ground wire (Black)

(To car chassis)

FM/AM antenna input

Fuse (10A)

Wiring harness
(Accessory

)

Ignition wire (Red)

Battery wire (Yellow)

ACC

Car fuse box

If no connections are made, do not let the wire come out from the tab.

To front left speaker

To front right speaker

To rear left speaker

To rear right speaker

White/Black

White

Gray/Black

Gray

Green/Black

Green

Purple/Black

Purple

Ignition key switch

Car fuse box
(Main fuse)

Front preout (KDC-MP443 only)

To Kenwood disc changer/
External optional accessory
(KDC-MP443 only)

Motor antenna control wire (Blue)

TEL mute wire (Brown)

Connect to the terminal that is grounded
when either the telephone rings or during
conversation.

⁄

To connect the Kenwood navigation system,

consult your navigation manual.

Power control/Motor antenna control wire
(Blue/White)

Connect either to the power control terminal
when using the optional power amplifier, or to
the antenna control terminal in the vehicle.

Depending on what antenna you are using, connect
either to the control terminal of the motor antenna,
or to the power terminal for the booster amplifier of
the film or short pole-type antenna.

Rear preout/ Subwoofer preout

–

FRONT

P.CONT

MUTE

ANT.
CONT

B64-4213-00̲00̲English.indd 17

08.7.25 10:23:18 AM

Содержание KDC-MP243





















Результаты поиска

Содержание KDC-MP243

Отзывы:

Похожие инструкции для KDC-MP243

Бренды по названию

Популярные бренды

Kenwood KDC-MP243, Инструкция по эксплуатации

Результаты поиска

Содержание KDC-MP243

Отзывы:

Похожие инструкции для KDC-MP243

Бренды по названию

Популярные бренды