background image

English

  

3

Installation

2

 CAUTION

•  Do not install in the below locations;

(Unstable location, In a location that interferes 
with driving, In a location that gets wet, In a dusty 
location, In a place that gets hot, In a place that gets 
direct sunlight, In a location that gets hit by hot air)

•  Do not install the unit under the carpet. Otherwise 

heat build-up occurs and the unit may be damaged.

•  Install this unit in a location which allows heat to 

easily dissipate.
Once installed, do not place any object on top of the 
unit.

•  The surface temperature of the amplifier will become 

hot during use. Install the amplifier in a place 
where people, resins, and other substances that are 
sensitive to heat will not come into contact with it.

•  This unit has cooling fan to decrease the internal 

temperature. Do not mount the unit in a place where 
the cooling fan and ducts of the unit are blocked. 
Blocking these openings will inhibit the cooling of 
the internal temperature and result in malfunction.

•  When making a hole under a seat, inside the trunk, 

or somewhere else in the vehicle, check that there 
is nothing hazardous on the opposite side such as a 
gasoline tank, brake pipe, or wiring harness, and be 
careful not to cause scratches or other damage.

•  Do not install near the dashboard, rear tray, or air bag 

safety parts.

•  The installation to the vehicle should securely fasten 

the unit to a place in which it will not obstruct 
driving. If the unit comes off due to a shock and hits 
a person or safety part, it may cause injury or an 
accident.

•  After installing the unit, check to make sure that 

electrical equipment such as the brake lamps, 
turn signal lamps and windshield wipers operate 
normally.

Installation board, etc.
(thickness : 15 mm or more)

Self-tapping screw
(ø4 × 16 mm)

330 mm

236 mm

Ø4.6

218.4 mm

230 mm

 Accessories

Part name

External 

View

Number of 

Items

Self-tapping screws 
(ø4 × 16 mm)

4

Terminal cover 
(Power terminal)

1

Speaker level input 
cable

1

Cooling fan
(KAC-M845)

Cooling fan
(KAC-M845)

B64-3924-00̲00̲M̲1English.indd   3

B64-3924-00̲00̲M̲1English.indd   3

07.11.15   11:29:31 AM

07.11.15   11:29:31 AM

Содержание KAC-M645









Отзывы: